Network Working Group                                       T. Dreibholz
Request for Comments: 5525                  University of Duisburg-Essen
Category: Experimental                                          J. Mulik
                                               Delaware State University
                                                              April 2009


             Reliable Server Pooling MIB Module Definition

Status of This Memo

   This memo defines an Experimental Protocol for the Internet
   community.  It does not specify an Internet standard of any kind.
   Discussion and suggestions for improvement are requested.
   Distribution of this memo is unlimited.

Copyright Notice

   Copyright (c) 2009 IETF Trust and the persons identified as the
   document authors.  All rights reserved.

   This document is subject to BCP 78 and the IETF Trust's Legal
   Provisions Relating to IETF Documents in effect on the date of
   publication of this document (http://trustee.ietf.org/license-info).
   Please review these documents carefully, as they describe your rights
   and restrictions with respect to this document.

Abstract

   Reliable Server Pooling (RSerPool) is a framework to provide reliable
   server pooling.  The RSerPool framework consists of two protocols:
   ASAP (Aggregate Server Access Protocol) and ENRP (Endpoint
   Handlespace Redundancy Protocol).  This document defines an SMIv2-
   compliant (Structure of Management Information Version 2) Management
   Information Base (MIB) module providing access to managed objects in
   an RSerPool implementation.















Dreibholz & Mulik             Experimental                      [Page 1]


RFC 5525                  RSerPool MIB Module                 April 2009


Table of Contents

   1. Introduction ....................................................2
   2. The Reliable Server Pooling (RSerPool) Framework ................2
   3. Conventions .....................................................2
   4. The Internet-Standard Management Framework ......................2
   5. Structure of the MIB ............................................3
      5.1. Access to Managed Objects on ENRP Servers .................10
      5.2. Access to Managed Objects on Pool Elements ................10
      5.3. Access to Managed Objects on Pool Users ...................11
      5.4. Persistency Behavior ......................................11
   6. Definitions ....................................................11
   7. Operational Considerations .....................................42
   8. Security Considerations ........................................42
   9. IANA Considerations ............................................43
   10. Acknowledgments ...............................................43
   11. References ....................................................44
      11.1. Normative References .....................................44
      11.2. Informative References ...................................44

1.  Introduction

   This memo defines a Management Information Base (MIB) module that
   describes managed objects for RSerPool implementations.

2.  The Reliable Server Pooling (RSerPool) Framework

   For a detailed overview of the documents that describe the current
   Reliable Server Pooling (RSerPool) framework, please refer to
   [RFC3237], [RFC5351], [RFC5352], [RFC5353], [RFC5354], [RFC5355], and
   [RFC5356].  A more informal introduction can be found at
   [RSerPoolPage] as well as in [Dre2006], [LCN2005], and [IJHIT2008].

3.  Conventions

   The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
   "SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this
   document are to be interpreted as described in [RFC2119].

4.  The Internet-Standard Management Framework

   For a detailed overview of the documents that describe the current
   Internet-Standard Management Framework, please refer to section 7 of
   RFC 3410 [RFC3410].

   Managed objects are accessed via a virtual information store, termed
   the Management Information Base or MIB.  MIB objects are generally
   accessed through the Simple Network Management Protocol (SNMP).



Dreibholz & Mulik             Experimental                      [Page 2]


RFC 5525                  RSerPool MIB Module                 April 2009


   Objects in the MIB are defined using the mechanisms defined in the
   Structure of Management Information (SMI).  This memo specifies a MIB
   module that is compliant to the SMIv2, which is described in STD 58,
   RFC 2578 [RFC2578], STD 58, RFC 2579 [RFC2579] and STD 58, RFC 2580
   [RFC2580].  The textual conventions are compliant to RFC 4001
   [RFC4001].

5.  Structure of the MIB

   The following diagram illustrates the structure of the MIB.

   Structure of MIB

  +--rserpoolMIB(125)
     |
     +--rserpoolMIBObjects(1)
     |  |
     |  +--rserpoolENRPServers(1)
     |  |  |
     |  |  +--rserpoolENRPTable(1)
     |  |  |  |
     |  |  |  +--rserpoolENRPEntry(1)
     |  |  |     |  Index: rserpoolENRPIndex
     |  |  |     |
     |  |  |     +-- ---- Unsigned  rserpoolENRPIndex(1)
     |  |  |     |        Range: 1..4294967295
     |  |  |     +-- -R-- String    rserpoolENRPOperationScope(2)
     |  |  |     |        Textual Conv.: RSerPoolOperationScopeTC
     |  |  |     |        Size: 0..65535
     |  |  |     +-- -R-- Unsigned  rserpoolENRPIdentifier(3)
     |  |  |     |        Textual Conv.: RSerPoolENRPServerIdentifierTC
     |  |  |     |        Range: 1..4294967295
     |  |  |     +-- -RW- String    rserpoolENRPDescription(4)
     |  |  |     |        Size: 0..255
     |  |  |     +-- -R-- TimeTicks rserpoolENRPUptime(5)
     |  |  |     +-- -R-- Unsigned  rserpoolENRPPort(6)
     |  |  |     |        Textual Conv.: InetPortNumber
     |  |  |     |        Range: 0..65535
     |  |  |     +-- -R-- Unsigned  rserpoolENRPASAPAnnouncePort(7)
     |  |  |     |        Textual Conv.: InetPortNumber
     |  |  |     |        Range: 0..65535
     |  |  |     +-- -R-- EnumVal   rserpoolENRPASAPAnnounceAddrType(8)
     |  |  |     |        Textual Conv.: InetAddressType
     |  |  |     |        Values: ipv4(1), ipv6(2)
     |  |  |     +-- -R-- String    rserpoolENRPASAPAnnounceAddr(9)
     |  |  |     |        Textual Conv.: InetAddress
     |  |  |     |        Size: 4 | 16




Dreibholz & Mulik             Experimental                      [Page 3]


RFC 5525                  RSerPool MIB Module                 April 2009


     |  |  |     +-- -R-- Unsigned  rserpoolENRPENRPAnnouncePort(10)
     |  |  |     |        Textual Conv.: InetPortNumber
     |  |  |     |        Range: 0..65535
     |  |  |     +-- -R-- EnumVal   rserpoolENRPENRPAnnounceAddrType(11)
     |  |  |     |        Textual Conv.: InetAddressType
     |  |  |     |        Values: ipv4(1), ipv6(2)
     |  |  |     +-- -R-- String    rserpoolENRPENRPAnnounceAddr(12)
     |  |  |              Textual Conv.: InetAddress
     |  |  |              Size: 4 | 16
     |  |  |
     |  |  +--rserpoolENRPPoolTable(3)
     |  |  |  |
     |  |  |  +--rserpoolENRPPoolEntry(1)
     |  |  |     |  Index: rserpoolENRPIndex, rserpoolENRPPoolIndex
     |  |  |     |
     |  |  |     +-- ---- Unsigned  rserpoolENRPPoolIndex(1)
     |  |  |     |        Range: 1..4294967295
     |  |  |     +-- -R-- String    rserpoolENRPPoolHandle(2)
     |  |  |              Textual Conv.: RSerPoolPoolHandleTC
     |  |  |              Size: 0..65535
     |  |  |
     |  |  +--rserpoolENRPPoolElementTable(4)
     |  |  |  |
     |  |  |  +--rserpoolENRPPoolElementEntry(1)
     |  |  |     |  Index: rserpoolENRPIndex, rserpoolENRPPoolIndex,
     |  |  |     |         rserpoolENRPPoolElementIndex
     |  |  |     |
     |  |  |     +-- ---- Unsigned  rserpoolENRPPoolElementIndex(1)
     |  |  |     |        Range: 1..4294967295
     |  |  |     +-- -R-- Unsigned  rserpoolENRPPoolElementID(2)
     |  |  |     |        Textual Conv.: RserpoolPoolElementIdentifierTC
     |  |  |     |        Range: 1..4294967295
     |  |  |     +-- -R-- Unsigned  rserpoolENRPASAPTransportPort(3)
     |  |  |     |        Textual Conv.: InetPortNumber
     |  |  |     |        Range: 0..65535
     |  |  |     +-- -R-- Unsigned  rserpoolENRPUserTransportProto(4)
     |  |  |     |        Range: 0..255
     |  |  |     +-- -R-- Unsigned  rserpoolENRPUserTransportPort(5)
     |  |  |     |        Textual Conv.: InetPortNumber
     |  |  |     |        Range: 0..65535
     |  |  |     +-- -R-- EnumVal   rserpoolENRPUserTransportUse(6)
     |  |  |     |        Textual Conv.: RSerPoolTransportUseTypeTC
     |  |  |     |        Values: dataOnly(0), dataPlusControl(1)
     |  |  |     +-- -R-- Unsigned  rserpoolENRPPolicyID(7)
     |  |  |     |        Textual Conv.: RSerPoolPolicyIdentifierTC
     |  |  |     |        Range: 1..4294967295
     |  |  |     +-- -R-- String    rserpoolENRPPolicyDescription(8)
     |  |  |     |        Size: 0..255



Dreibholz & Mulik             Experimental                      [Page 4]


RFC 5525                  RSerPool MIB Module                 April 2009


     |  |  |     +-- -R-- Unsigned  rserpoolENRPPolicyWeight(9)
     |  |  |     |        Textual Conv.: RSerPoolPolicyWeightTC
     |  |  |     |        Range: 0..4294967295
     |  |  |     +-- -R-- Unsigned  rserpoolENRPPolicyLoad(10)
     |  |  |     |        Textual Conv.: RSerPoolPolicyLoadTC
     |  |  |     |        Range: 0..4294967295
     |  |  |     +-- -R-- Unsigned  rserpoolENRPPolicyLoadDeg(11)
     |  |  |     |        Textual Conv.: RSerPoolPolicyLoadTC
     |  |  |     |        Range: 0..4294967295
     |  |  |     +-- -R-- TimeTicks rserpoolENRPRegistrationLife(12)
     |  |  |     +-- -R-- Unsigned  rserpoolENRPHomeENRPServer(13)
     |  |  |              Textual Conv.: RSerPoolENRPServerIdentifierTC
     |  |  |              Range: 1..4294967295
     |  |  |
     |  |  +--rserpoolENRPASAPAddrTable(5)
     |  |  |  |
     |  |  |  +--rserpoolENRPASAPAddrTableEntry(1)
     |  |  |     |  Index: rserpoolENRPIndex, rserpoolENRPPoolIndex,
     |  |  |     |         rserpoolENRPPoolElementIndex,
     |  |  |     |         rserpoolENRPASAPAddrTableIndex
     |  |  |     |
     |  |  |     +-- ---- Unsigned  rserpoolENRPASAPAddrTableIndex(1)
     |  |  |     |        Range: 1..4294967295
     |  |  |     +-- -R-- EnumVal   rserpoolENRPASAPL3Type(2)
     |  |  |     |        Textual Conv.: InetAddressType
     |  |  |     |        Values: ipv4(1), ipv6(2)
     |  |  |     +-- -R-- String    rserpoolENRPASAPL3Addr(3)
     |  |  |              Textual Conv.: InetAddress
     |  |  |              Size: 4 | 16
     |  |  |
     |  |  +--rserpoolENRPUserAddrTable(6)
     |  |  |  |
     |  |  |  +--rserpoolENRPUserAddrTableEntry(1)
     |  |  |     |  Index: rserpoolENRPIndex, rserpoolENRPPoolIndex,
     |  |  |     |         rserpoolENRPPoolElementIndex,
     |  |  |     |         rserpoolENRPUserAddrTableIndex
     |  |  |     |
     |  |  |     +-- ---- Unsigned  rserpoolENRPUserAddrTableIndex(1)
     |  |  |     |        Range: 1..4294967295
     |  |  |     +-- -R-- EnumVal   rserpoolENRPUserL3Type(2)
     |  |  |     |        Textual Conv.: InetAddressType
     |  |  |     |        Values: unknown(0), ipv4(1), ipv6(2)
     |  |  |     +-- -R-- String    rserpoolENRPUserL3Addr(3)
     |  |  |     |        Textual Conv.: InetAddress
     |  |  |     |        Size: 0 | 4 | 16
     |  |  |     +-- -R-- String    rserpoolENRPUserL3Opaque(4)
     |  |  |              Textual Conv.: RSerPoolOpaqueAddressTC
     |  |  |              Size: 0..65535



Dreibholz & Mulik             Experimental                      [Page 5]


RFC 5525                  RSerPool MIB Module                 April 2009


     |  |  |
     |  |  +--rserpoolENRPENRPAddrTable(7)
     |  |  |  |
     |  |  |  +--rserpoolENRPENRPAddrTableEntry(1)
     |  |  |     |  Index: rserpoolENRPIndex,
     |  |  |     |         rserpoolENRPENRPAddrTableIndex
     |  |  |     |
     |  |  |     +-- ---- Unsigned  rserpoolENRPENRPAddrTableIndex(1)
     |  |  |     |        Range: 1..4294967295
     |  |  |     +-- -R-- EnumVal   rserpoolENRPENRPL3Type(2)
     |  |  |     |        Textual Conv.: InetAddressType
     |  |  |     |        Values: ipv4(1), ipv6(2)
     |  |  |     +-- -R-- String    rserpoolENRPENRPL3Addr(3)
     |  |  |              Textual Conv.: InetAddress
     |  |  |              Size: 4 | 16
     |  |  |
     |  |  +--rserpoolENRPPeerTable(8)
     |  |  |  |
     |  |  |  +--rserpoolENRPPeerEntry(1)
     |  |  |     |  Index: rserpoolENRPPeerIndex
     |  |  |     |
     |  |  |     +-- ---- Unsigned  rserpoolENRPPeerIndex(1)
     |  |  |     |        Range: 1..4294967295
     |  |  |     +-- -R-- Unsigned  rserpoolENRPPeerIdentifier(2)
     |  |  |     |        Textual Conv.: RSerPoolENRPServerIdentifierTC
     |  |  |     |        Range: 1..4294967295
     |  |  |     +-- -R-- Unsigned  rserpoolENRPPeerPort(3)
     |  |  |     |        Textual Conv.: InetPortNumber
     |  |  |     |        Range: 0..65535
     |  |  |     +-- -R-- TimeTicks rserpoolENRPPeerLastHeard(4)
     |  |  |
     |  |  +--rserpoolENRPPeerAddrTable(9)
     |  |     |
     |  |     +--rserpoolENRPPeerAddrTableEntry(1)
     |  |        |  Index: rserpoolENRPPeerIndex,
     |  |  |     |         rserpoolENRPPeerAddrTableIndex
     |  |        |
     |  |        +-- ---- Unsigned  rserpoolENRPPeerAddrTableIndex(1)
     |  |        |        Range: 1..4294967295
     |  |        +-- -R-- EnumVal   rserpoolENRPPeerL3Type(2)
     |  |        |        Textual Conv.: InetAddressType
     |  |        |        Values: ipv4(1), ipv6(2)
     |  |        +-- -R-- String    rserpoolENRPPeerL3Addr(3)
     |  |                 Textual Conv.: InetAddress
     |  |                 Size: 4 | 16
     |  |
     |  +--rserpoolPoolElements(2)
     |  |  |



Dreibholz & Mulik             Experimental                      [Page 6]


RFC 5525                  RSerPool MIB Module                 April 2009


     |  |  +--rserpoolPETable(1)
     |  |  |  |
     |  |  |  +--rserpoolPEEntry(1)
     |  |  |     |  Index: rserpoolPEIndex
     |  |  |     |
     |  |  |     +-- ---- Unsigned  rserpoolPEIndex(1)
     |  |  |     |        Range: 1..4294967295
     |  |  |     +-- -R-- String    rserpoolPEOperationScope(2)
     |  |  |     |        Textual Conv.: RSerPoolOperationScopeTC
     |  |  |     |        Size: 0..65535
     |  |  |     +-- -RW- String    rserpoolPEPoolHandle(3)
     |  |  |     |        Textual Conv.: RSerPoolPoolHandleTC
     |  |  |     |        Size: 0..65535
     |  |  |     +-- -R-- Unsigned  rserpoolPEIdentifier(4)
     |  |  |     |        Textual Conv.: RserpoolPoolElementIdentifierTC
     |  |  |     |        Range: 1..4294967295
     |  |  |     +-- -RW- String    rserpoolPEDescription(5)
     |  |  |     |        Size: 0..255
     |  |  |     +-- -R-- TimeTicks rserpoolPEUptime(6)
     |  |  |     +-- -R-- Unsigned  rserpoolPEASAPTransportPort(7)
     |  |  |     |        Textual Conv.: InetPortNumber
     |  |  |     |        Range: 0..65535
     |  |  |     +-- -R-- Unsigned  rserpoolPEUserTransportProto(8)
     |  |  |     |        Range: 0..255
     |  |  |     +-- -R-- Unsigned  rserpoolPEUserTransportPort(9)
     |  |  |     |        Textual Conv.: InetPortNumber
     |  |  |     |        Range: 0..65535
     |  |  |     +-- -R-- EnumVal   rserpoolPEUserTransportUse(10)
     |  |  |     |        Textual Conv.: RSerPoolTransportUseTypeTC
     |  |  |     |        Values: dataOnly(0), dataPlusControl(1)
     |  |  |     +-- -RW- Unsigned  rserpoolPEPolicyID(11)
     |  |  |     |        Textual Conv.: RSerPoolPolicyIdentifierTC
     |  |  |     |        Range: 1..4294967295
     |  |  |     +-- -RW- String    rserpoolPEPolicyDescription(12)
     |  |  |     |        Size: 0..255
     |  |  |     +-- -RW- Unsigned  rserpoolPEPolicyWeight(13)
     |  |  |     |        Textual Conv.: RSerPoolPolicyWeightTC
     |  |  |     |        Range: 0..4294967295
     |  |  |     +-- -R-- Unsigned  rserpoolPEPolicyLoad(14)
     |  |  |     |        Textual Conv.: RSerPoolPolicyLoadTC
     |  |  |     |        Range: 0..4294967295
     |  |  |     +-- -RW- Unsigned  rserpoolPEPolicyLoadDeg(15)
     |  |  |     |        Textual Conv.: RSerPoolPolicyLoadTC
     |  |  |     |        Range: 0..4294967295
     |  |  |     +-- -RW- TimeTicks rserpoolPERegistrationLife(16)
     |  |  |     +-- -R-- Unsigned  rserpoolPEHomeENRPServer(17)
     |  |  |              Textual Conv.: RSerPoolENRPServerIdentifierTC
     |  |  |              Range: 1..4294967295



Dreibholz & Mulik             Experimental                      [Page 7]


RFC 5525                  RSerPool MIB Module                 April 2009


     |  |  |
     |  |  +--rserpoolPEASAPAddrTable(2)
     |  |  |  |
     |  |  |  +--rserpoolPEASAPAddrTableEntry(1)
     |  |  |     |  Index: rserpoolPEIndex, rserpoolPEASAPAddrTableIndex
     |  |  |     |
     |  |  |     +-- ---- Unsigned  rserpoolPEASAPAddrTableIndex(1)
     |  |  |     |        Range: 1..4294967295
     |  |  |     +-- -R-- EnumVal   rserpoolPEASAPL3Type(2)
     |  |  |     |        Textual Conv.: InetAddressType
     |  |  |     |        Values: ipv4(1), ipv6(2)
     |  |  |     +-- -R-- String    rserpoolPEASAPL3Addr(3)
     |  |  |              Textual Conv.: InetAddress
     |  |  |              Size: 4 | 16
     |  |  |
     |  |  +--rserpoolPEUserAddrTable(6)
     |  |     |
     |  |     +--rserpoolPEUserAddrTableEntry(1)
     |  |        |  Index: rserpoolPEIndex, rserpoolPEUserAddrTableIndex
     |  |        |
     |  |        +-- ---- Unsigned  rserpoolPEUserAddrTableIndex(1)
     |  |        |        Range: 1..4294967295
     |  |        +-- -R-- EnumVal   rserpoolPEUserL3Type(2)
     |  |        |        Textual Conv.: InetAddressType
     |  |        |        Values: unknown(0), ipv4(1), ipv6(2)
     |  |        +-- -R-- String    rserpoolPEUserL3Addr(3)
     |  |        |        Textual Conv.: InetAddress
     |  |        |        Size: 0 | 4 | 16
     |  |        +-- -R-- String    rserpoolPEUserL3Opaque(4)
     |  |                 Textual Conv.: RSerPoolOpaqueAddressTC
     |  |                 Size: 0..65535
     |  |
     |  +--rserpoolPoolUsers(3)
     |     |
     |     +--rserpoolPUTable(1)
     |        |
     |        +--rserpoolPUEntry(1)
     |           |  Index: rserpoolPUIndex
     |           |
     |           +-- ---- Unsigned  rserpoolPUIndex(1)
     |           |        Range: 1..4294967295
     |           +-- -R-- String    rserpoolPUOperationScope(2)
     |           |        Textual Conv.: RSerPoolOperationScopeTC
     |           |        Size: 0..65535
     |           +-- -RW- String    rserpoolPUPoolHandle(3)
     |           |        Textual Conv.: RSerPoolPoolHandleTC
     |           |        Size: 0..65535
     |           +-- -RW- String    rserpoolPUDescription(4)



Dreibholz & Mulik             Experimental                      [Page 8]


RFC 5525                  RSerPool MIB Module                 April 2009


     |           |        Size: 0..255
     |           +-- -R-- TimeTicks rserpoolPUUptime(5)
     |
     +--rserpoolMIBConformance(2)
        |
        +--rserpoolMIBCompliances(1)
        |  |
        |  +--rserpoolMIBCompliance(1)
        |
        +--rserpoolMIBGroups(2)
           |
           +--rserpoolENRPGroup(1)
           +--rserpoolPEGroup(2)
           +--rserpoolPUGroup(3)

   As the figure shows, the MIB consists of three main branches:
   "rserpoolENRPServers", "rserpoolPoolElements", and
   "rserpoolPoolUsers".  The first branch, "rserpoolENRPServers", is
   used to access managed objects in the set of ENRP servers running on
   a given host.  While it is assumed that it does not make much sense
   to run multiple ENRP servers for the same operation scope on one
   host, running multiple ENRP servers for different operation scopes is
   very likely when the ENRP server processes run on routers.
   Therefore, the MIB has to be able to manage multiple ENRP servers on
   the same host.

   "rserpoolPoolElements" is used to access managed objects in the set
   of pool elements that are running on a given host.

   The third branch, "rserpoolPoolUsers", is used to access managed
   objects in the set of pool users that are running on a given host.

   Note: "rserpoolENRPServers" is filled on hosts running ENRP server
   instances, "rserpoolPoolElements" is filled on hosts running pool
   element instances, and "rserpoolPoolUsers" is filled on hosts running
   pool user instances.  Of course, multiple different components may
   run on the same host, which leads to filling of multiple different
   branches.

   In fact, the structure of the three branches is very similar.
   Because the other two branches are so similar, we describe only the
   first branch in detail, and provide a summary description of the
   second and third branch.  We now proceed with a description of the
   branches.







Dreibholz & Mulik             Experimental                      [Page 9]


RFC 5525                  RSerPool MIB Module                 April 2009


5.1.  Access to Managed Objects on ENRP Servers

   The first branch describes managed objects at a set of ENRP servers.
   Any given ENRP server of this set will, at a certain moment in time,
   have registration information for a set of active pools.  Each of
   these pools in turn may have a list of pool elements that are
   registered under that pool.  To allow this information to be
   retrieved via SNMP, the ERNP server branch of the RSerPool MIB uses
   the table-in-table technique described in [SNMPMIBS].

   Specifically, the ENRP servers branch creates four levels of nesting,
   as indicated in the following diagram:

   Nesting of the ENRP Server Branch

   Nesting Structure:

    Level 1: rserpoolENRPTable

    Level 2:    rserpoolENRPPoolTable
    Level 3:       rserpoolENRPPoolElementTable
    Level 4:          rserpoolENRPASAPAddrTable
                      rserpoolENRPUserAddrTable

    Level 2:    rserpoolENRPENRPAddrTable

    Level 2:    rserpoolENRPPeerTable
    Level 3:       rserpoolENRPPeerAddrTable

5.2.  Access to Managed Objects on Pool Elements

   The construction of the Pool Elements branch is very similar to the
   pool elements table of the ENRP servers branch.  But instead of
   grouping the pool elements into pools (which does not make sense
   here), the pool elements table is the top of the hierarchy, and each
   pool element entry specifies its operation scope and pool handle.

   That is, the nesting structure is as follows:

   Nesting of the Pool Elements Branch

    Level 1:    rserpoolPETable
    Level 2:       rserpoolPEASAPAddrTable
                   rserpoolPEUserAddrTable







Dreibholz & Mulik             Experimental                     [Page 10]


RFC 5525                  RSerPool MIB Module                 April 2009


5.3.  Access to Managed Objects on Pool Users

   For the Pool Users branch, it is only necessary to list the pool user
   instances, including their operation scope and pool handle.

5.4.  Persistency Behavior

   Upon changes of writable objects, an implementation SHOULD store the
   new values in a persistent manner if it has the capability to do
   this.  An implementation SHOULD use these stored values upon reset or
   reinitialization.

6.  Definitions

RSERPOOL-MIB DEFINITIONS ::= BEGIN

IMPORTS
   MODULE-IDENTITY, OBJECT-TYPE, experimental,
   TimeTicks, Unsigned32
      FROM SNMPv2-SMI
   TEXTUAL-CONVENTION
      FROM SNMPv2-TC
   MODULE-COMPLIANCE, OBJECT-GROUP
      FROM SNMPv2-CONF
   InetAddressType, InetAddress, InetPortNumber
      FROM INET-ADDRESS-MIB;

-- ## Module definition ###########################################
rserpoolMIB MODULE-IDENTITY
   LAST-UPDATED
      "200904070000Z" -- April 07, 2009
   ORGANIZATION
      "IEM-TdR, UNIVERSITY OF DUISBURG-ESSEN"
   CONTACT-INFO
      " THOMAS-DREIBHOLZ

         Postal:  University of Duisburg-Essen
                  Institute for Experimental Mathematics
                  Ellernstrasse 29
                  D-45326 Essen
                  Germany
         Phone:   +49-201-183-7637
         Fax:     +49-201-183-7673
         Email:   dreibh@iem.uni-due.de







Dreibholz & Mulik             Experimental                     [Page 11]


RFC 5525                  RSerPool MIB Module                 April 2009


      JAIWANT-MULIK

         Postal:  Delaware State University
                  CIS Department
                  1200 N. DuPont Hw
                  Dover, DE
                  USA 19904
         Phone:   +1-302-857-7910
         Fax:     +1-302-857-6552
         Email:   jaiwant@mulik.com"
      DESCRIPTION
         "The MIB module for managing an RSerPool implementation.

          Copyright (c) 2009 IETF Trust and the persons identified as
          authors of the code.  All rights reserved.

          Redistribution and use in source and binary forms, with or
          without modification, are permitted provided that the
          following conditions are met:

          - Redistributions of source code must retain the above
            copyright notice, this list of conditions and the
            following disclaimer.

          - Redistributions in binary form must reproduce the above
            copyright notice, this list of conditions and the
            following disclaimer in the documentation and/or other
            materials provided with the distribution.

          - Neither the name of Internet Society, IETF or IETF Trust,
            nor the names of specific contributors, may be used to
            endorse or promote products derived from this software
            without specific prior written permission.

          THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND
          CONTRIBUTORS 'AS IS' AND ANY EXPRESS OR IMPLIED WARRANTIES,
          INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
          MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
          DISCLAIMED.  IN NO EVENT SHALL THE COPYRIGHT OWNER OR
          CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL,
          SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT
          NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES;
          LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION)
          HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN
          CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR
          OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
          SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH
          DAMAGE.



Dreibholz & Mulik             Experimental                     [Page 12]


RFC 5525                  RSerPool MIB Module                 April 2009


          This version of this MIB module is part of RFC 5525;
          see the RFC itself for full legal notices."

      REVISION
         "200904070000Z" -- April 07, 2009
      DESCRIPTION
         "This version of the MIB module is published as RFC 5525"
      ::= { experimental 125 }

-- ## RSerPool type definitions ###################################
RSerPoolENRPServerIdentifierTC ::= TEXTUAL-CONVENTION
   DISPLAY-HINT "x"
   STATUS       current
   DESCRIPTION  "The ID of an ENRP server"
   SYNTAX       Unsigned32 (1..4294967295)

RSerPoolOperationScopeTC ::= TEXTUAL-CONVENTION
   DISPLAY-HINT "1024t"
   STATUS       current
   DESCRIPTION  "The ID of an operation scope"
   SYNTAX       OCTET STRING (SIZE (0..65535))

RSerPoolPoolHandleTC ::= TEXTUAL-CONVENTION
   DISPLAY-HINT "1024t"
   STATUS       current
   DESCRIPTION  "The pool handle"
   SYNTAX       OCTET STRING (SIZE (0..65535))

RserpoolPoolElementIdentifierTC ::= TEXTUAL-CONVENTION
   DISPLAY-HINT "x"
   STATUS       current
   DESCRIPTION  "The pool element ID"
   SYNTAX       Unsigned32 (1..4294967295)

RSerPoolPolicyIdentifierTC ::= TEXTUAL-CONVENTION
   DISPLAY-HINT "x"
   STATUS       current
   DESCRIPTION  "The ID of the pool policy"
   SYNTAX       Unsigned32 (1..4294967295)

RSerPoolPolicyLoadTC ::= TEXTUAL-CONVENTION
   DISPLAY-HINT "d"
   STATUS       current
   DESCRIPTION  "The load status of a pool element"
   SYNTAX       Unsigned32 (0..4294967295)






Dreibholz & Mulik             Experimental                     [Page 13]


RFC 5525                  RSerPool MIB Module                 April 2009


RSerPoolPolicyWeightTC ::= TEXTUAL-CONVENTION
   DISPLAY-HINT "d"
   STATUS       current
   DESCRIPTION  "The weight of a pool element"
   SYNTAX       Unsigned32 (0..4294967295)

RSerPoolTransportUseTypeTC ::= TEXTUAL-CONVENTION
   STATUS       current
   DESCRIPTION "The transport use of a pool element"
   SYNTAX       INTEGER {
      dataOnly(0),
      dataPlusControl(1)
   }

RSerPoolOpaqueAddressTC ::= TEXTUAL-CONVENTION
   DISPLAY-HINT "1024t"
   STATUS       current
   DESCRIPTION  "Opaque address"
   SYNTAX       OCTET STRING  (SIZE (0..65535))

-- ## Top-level definitions #######################################
rserpoolMIBObjects     OBJECT IDENTIFIER ::= { rserpoolMIB 1 }
rserpoolMIBConformance OBJECT IDENTIFIER ::= { rserpoolMIB 2 }

rserpoolENRPServers    OBJECT IDENTIFIER ::= { rserpoolMIBObjects 1 }
rserpoolPoolElements   OBJECT IDENTIFIER ::= { rserpoolMIBObjects 2 }
rserpoolPoolUsers      OBJECT IDENTIFIER ::= { rserpoolMIBObjects 3 }

-- ################################################################
-- #### ENRP Servers Section                                   ####
-- ################################################################

-- ## Definition of the ENRP server table #########################
rserpoolENRPTable OBJECT-TYPE
   SYNTAX     SEQUENCE OF RserpoolENRPEntry
   MAX-ACCESS not-accessible
   STATUS     current
   DESCRIPTION
      "The table listing of ENRP servers."
   ::= { rserpoolENRPServers 1 }

rserpoolENRPEntry OBJECT-TYPE
   SYNTAX     RserpoolENRPEntry
   MAX-ACCESS not-accessible
   STATUS     current






Dreibholz & Mulik             Experimental                     [Page 14]


RFC 5525                  RSerPool MIB Module                 April 2009


   DESCRIPTION
      "An ENRP server entry in the table listing of ENRP
      servers."
   INDEX { rserpoolENRPIndex }
   ::= { rserpoolENRPTable 1 }

RserpoolENRPEntry ::= SEQUENCE {
rserpoolENRPIndex                Unsigned32,
rserpoolENRPOperationScope       RSerPoolOperationScopeTC,
rserpoolENRPIdentifier           RSerPoolENRPServerIdentifierTC,
rserpoolENRPDescription          OCTET STRING,
rserpoolENRPUptime               TimeTicks,
rserpoolENRPPort                 InetPortNumber,
rserpoolENRPASAPAnnouncePort     InetPortNumber,
rserpoolENRPASAPAnnounceAddrType InetAddressType,
rserpoolENRPASAPAnnounceAddr     InetAddress,
rserpoolENRPENRPAnnouncePort     InetPortNumber,
rserpoolENRPENRPAnnounceAddrType InetAddressType,
rserpoolENRPENRPAnnounceAddr     InetAddress }

rserpoolENRPIndex OBJECT-TYPE
   SYNTAX     Unsigned32 (1..4294967295)
   MAX-ACCESS not-accessible
   STATUS     current
   DESCRIPTION
      "An integer to uniquely identify an ENRP server."
   ::= { rserpoolENRPEntry 1 }

rserpoolENRPOperationScope OBJECT-TYPE
   SYNTAX     RSerPoolOperationScopeTC
   MAX-ACCESS read-only
   STATUS     current
   DESCRIPTION
      "The definition of the operation scope of this ENRP server."
   REFERENCE
      "Section 1.2 of RFC 3237 defines the term operation scope."
   ::= { rserpoolENRPEntry 2 }

rserpoolENRPIdentifier OBJECT-TYPE
   SYNTAX     RSerPoolENRPServerIdentifierTC
   MAX-ACCESS read-only
   STATUS     current
   DESCRIPTION
      "The ENRP server identifier of this ENRP server."
   REFERENCE
      "Section 3.1 of RFC 5351 explains the ENRP server identifier."
   ::= { rserpoolENRPEntry 3 }




Dreibholz & Mulik             Experimental                     [Page 15]


RFC 5525                  RSerPool MIB Module                 April 2009


rserpoolENRPDescription OBJECT-TYPE
   SYNTAX     OCTET STRING (SIZE (0..255))
   MAX-ACCESS read-write
   STATUS     current
   DESCRIPTION
      "A textual description of this ENRP server, e.g., its location
      and a contact address of its administrator.

      This object SHOULD be maintained in a persistent manner."
   ::= { rserpoolENRPEntry 4 }

rserpoolENRPUptime OBJECT-TYPE
   SYNTAX     TimeTicks
   MAX-ACCESS read-only
   STATUS     current
   DESCRIPTION
      "The ENRP service uptime of this ENRP server."
   ::= { rserpoolENRPEntry 5 }

rserpoolENRPPort OBJECT-TYPE
   SYNTAX     InetPortNumber
   MAX-ACCESS read-only
   STATUS     current
   DESCRIPTION
      "The Stream Control Transmission Protocol (SCTP) port number of
      the ENRP protocol endpoint of this ENRP server."
   REFERENCE
      "RFC 5353 defines the ENRP protocol."
   ::= { rserpoolENRPEntry 6 }

rserpoolENRPASAPAnnouncePort OBJECT-TYPE
   SYNTAX     InetPortNumber
   MAX-ACCESS read-only
   STATUS     current
   DESCRIPTION
      "The destination UDP port number to which ASAP multicast announce
      messages are sent."
   REFERENCE
      "Section 3.2 of RFC 5351 explains the server-discovery mechanism
      using ASAP announces."
   ::= { rserpoolENRPEntry 7 }

rserpoolENRPASAPAnnounceAddrType OBJECT-TYPE
   SYNTAX     InetAddressType { ipv4(1), ipv6(2) }
   MAX-ACCESS read-only
   STATUS     current





Dreibholz & Mulik             Experimental                     [Page 16]


RFC 5525                  RSerPool MIB Module                 April 2009


   DESCRIPTION
      "The network-layer protocol over which ASAP multicast announce
      messages are sent."
   REFERENCE
      "Section 3.2 of RFC 5351 explains the server-discovery mechanism
      using ASAP announces."
   ::= { rserpoolENRPEntry 8 }

rserpoolENRPASAPAnnounceAddr OBJECT-TYPE
   SYNTAX     InetAddress (SIZE(4|16))
   MAX-ACCESS read-only
   STATUS     current
   DESCRIPTION
      "The destination IP multicast address to which ASAP multicast
      announce messages are sent.  The type of this address is
      given in rserpoolENRPASAPAnnounceAddrType."
   REFERENCE
      "Section 3.2 of RFC 5351 explains the server-discovery mechanism
      using ASAP announces."
   ::= { rserpoolENRPEntry 9 }

rserpoolENRPENRPAnnouncePort OBJECT-TYPE
   SYNTAX     InetPortNumber
   MAX-ACCESS read-only
   STATUS     current
   DESCRIPTION
      "The destination UDP port number to which ENRP multicast announce
      messages are sent."
   REFERENCE
      "Section 3.1 of RFC 5353 explains the ENRP multicast
      announce mechanism."
   ::= { rserpoolENRPEntry 10 }

rserpoolENRPENRPAnnounceAddrType OBJECT-TYPE
   SYNTAX     InetAddressType { ipv4(1), ipv6(2) }
   MAX-ACCESS read-only
   STATUS     current
   DESCRIPTION
      "The network-layer protocol over which ENRP multicast announce
      messages are sent."
   REFERENCE
      "Section 3.1 of RFC 5353 explains the ENRP multicast
      announce mechanism."
   ::= { rserpoolENRPEntry 11 }

rserpoolENRPENRPAnnounceAddr OBJECT-TYPE
   SYNTAX     InetAddress (SIZE(4|16))
   MAX-ACCESS read-only



Dreibholz & Mulik             Experimental                     [Page 17]


RFC 5525                  RSerPool MIB Module                 April 2009


   STATUS     current
   DESCRIPTION
      "The destination multicast IP address to which ENRP multicast
      announce messages are sent.  The type of this address
      is given in rserpoolENRPENRPAnnounceAddrType."
   REFERENCE
      "Section 3.1 of RFC 5353 explains the ENRP multicast
      announce mechanism."
   ::= { rserpoolENRPEntry 12 }

-- ## Definition of the pool table ################################
rserpoolENRPPoolTable OBJECT-TYPE
   SYNTAX     SEQUENCE OF RserpoolENRPPoolEntry
   MAX-ACCESS not-accessible
   STATUS     current
   DESCRIPTION
      "The table listing of pools."
   ::= { rserpoolENRPServers 3 }

rserpoolENRPPoolEntry OBJECT-TYPE
   SYNTAX     RserpoolENRPPoolEntry
   MAX-ACCESS not-accessible
   STATUS     current
   DESCRIPTION
      "The pool entry in the table listing of pools."
   INDEX { rserpoolENRPIndex, rserpoolENRPPoolIndex }
   ::= { rserpoolENRPPoolTable 1 }

RserpoolENRPPoolEntry ::= SEQUENCE {
   rserpoolENRPPoolIndex  Unsigned32,
   rserpoolENRPPoolHandle RSerPoolPoolHandleTC }

rserpoolENRPPoolIndex OBJECT-TYPE
   SYNTAX     Unsigned32 (1..4294967295)
   MAX-ACCESS not-accessible
   STATUS     current
   DESCRIPTION
      "An integer to uniquely identify a pool."
   ::= { rserpoolENRPPoolEntry 1 }

rserpoolENRPPoolHandle OBJECT-TYPE
   SYNTAX     RSerPoolPoolHandleTC
   MAX-ACCESS read-only
   STATUS     current
   DESCRIPTION
      "The pool handle of this pool."
   REFERENCE
      "Section 1.2 of RFC 3237 defines the term pool handle."



Dreibholz & Mulik             Experimental                     [Page 18]


RFC 5525                  RSerPool MIB Module                 April 2009


   ::= { rserpoolENRPPoolEntry 2 }

-- ## Definition of the pool element table ########################
rserpoolENRPPoolElementTable OBJECT-TYPE
   SYNTAX     SEQUENCE OF RserpoolENRPPoolElementEntry
   MAX-ACCESS not-accessible
   STATUS     current
   DESCRIPTION
      "The table listing of pool elements."
   ::= { rserpoolENRPServers 4 }

rserpoolENRPPoolElementEntry OBJECT-TYPE
   SYNTAX     RserpoolENRPPoolElementEntry
   MAX-ACCESS not-accessible
   STATUS     current
   DESCRIPTION
      "A pool element in the table listing of pool elements."
   INDEX {
      rserpoolENRPIndex,
      rserpoolENRPPoolIndex,
      rserpoolENRPPoolElementIndex }
   ::= { rserpoolENRPPoolElementTable 1 }

RserpoolENRPPoolElementEntry ::= SEQUENCE {
   rserpoolENRPPoolElementIndex   Unsigned32,
   rserpoolENRPPoolElementID      RserpoolPoolElementIdentifierTC,
   rserpoolENRPASAPTransportPort  InetPortNumber,
   rserpoolENRPUserTransportProto Unsigned32,
   rserpoolENRPUserTransportPort  InetPortNumber,
   rserpoolENRPUserTransportUse   RSerPoolTransportUseTypeTC,
   rserpoolENRPPolicyID           RSerPoolPolicyIdentifierTC,
   rserpoolENRPPolicyDescription  OCTET STRING,
   rserpoolENRPPolicyWeight       RSerPoolPolicyWeightTC,
   rserpoolENRPPolicyLoad         RSerPoolPolicyLoadTC,
   rserpoolENRPPolicyLoadDeg      RSerPoolPolicyLoadTC,
   rserpoolENRPRegistrationLife   TimeTicks,
   rserpoolENRPHomeENRPServer     RSerPoolENRPServerIdentifierTC }


rserpoolENRPPoolElementIndex OBJECT-TYPE
   SYNTAX     Unsigned32 (1..4294967295)
   MAX-ACCESS not-accessible
   STATUS     current








Dreibholz & Mulik             Experimental                     [Page 19]


RFC 5525                  RSerPool MIB Module                 April 2009


   DESCRIPTION
      "An integer to uniquely identify a pool element.  Note,
      that uniqueness of a pool element identifier in the pool
      is not enforced; therefore, this index is required here!"
   ::={ rserpoolENRPPoolElementEntry 1 }

rserpoolENRPPoolElementID OBJECT-TYPE
   SYNTAX     RserpoolPoolElementIdentifierTC
   MAX-ACCESS read-only
   STATUS     current
   DESCRIPTION
      "The pool element identifier of this pool element."
   REFERENCE
      "Section 2.2 of RFC 5351 explains the pool element identifier
      usage."
   ::={ rserpoolENRPPoolElementEntry 2 }

rserpoolENRPASAPTransportPort OBJECT-TYPE
   SYNTAX     InetPortNumber
   MAX-ACCESS read-only
   STATUS     current
   DESCRIPTION
      "The SCTP port number of the ASAP endpoint of this pool
      element."
   REFERENCE
      "Section 3.10 of RFC 5354 defines the ASAP Transport Parameter of
      which the port number is given here."
   ::= { rserpoolENRPPoolElementEntry 3 }

rserpoolENRPUserTransportProto OBJECT-TYPE
   SYNTAX     Unsigned32 (0..255)
   MAX-ACCESS read-only
   STATUS     current
   DESCRIPTION
      "The transport protocol number of the service endpoint
      of this pool element."
   REFERENCE
      "Section 3.10 of RFC 5354 defines the User Transport Parameter of
      which the transport protocol number is given here."
   ::= { rserpoolENRPPoolElementEntry 4 }

rserpoolENRPUserTransportPort OBJECT-TYPE
   SYNTAX     InetPortNumber
   MAX-ACCESS read-only
   STATUS     current
   DESCRIPTION
      "The transport protocol's port number of the service
      endpoint of this pool element."



Dreibholz & Mulik             Experimental                     [Page 20]


RFC 5525                  RSerPool MIB Module                 April 2009


   REFERENCE
      "Section 3.10 of RFC 5354 defines the User Transport Parameter of
      which the port number is given here."
   ::= { rserpoolENRPPoolElementEntry 5 }

rserpoolENRPUserTransportUse OBJECT-TYPE
   SYNTAX     RSerPoolTransportUseTypeTC
   MAX-ACCESS read-only
   STATUS     current
   DESCRIPTION
      "The transport use of the service endpoint of this pool
      element."
   REFERENCE
      "Section 3.10 of RFC 5354 defines the User Transport Parameter of
      which the transport use is given here."
   ::= { rserpoolENRPPoolElementEntry 6 }

rserpoolENRPPolicyID OBJECT-TYPE
   SYNTAX     RSerPoolPolicyIdentifierTC
   MAX-ACCESS read-only
   STATUS     current
   DESCRIPTION
      "The pool policy of this pool element."
   REFERENCE
      "Section 3.8 of RFC 5354 defines the Member Selection Policy
      Parameter of which the policy identifier is given here."
   ::= { rserpoolENRPPoolElementEntry 7 }

rserpoolENRPPolicyDescription OBJECT-TYPE
   SYNTAX     OCTET STRING (SIZE (0..255))
   MAX-ACCESS read-only
   STATUS     current
   DESCRIPTION
      "The textual description of the pool policy of this pool
      element."
   ::= { rserpoolENRPPoolElementEntry 8 }

rserpoolENRPPolicyWeight OBJECT-TYPE
   SYNTAX     RSerPoolPolicyWeightTC
   MAX-ACCESS read-only
   STATUS     current
   DESCRIPTION
      "The pool policy's weight parameter for this pool element."
   REFERENCE
      "Section 3.8 of RFC 5354 defines the Member Selection Policy
      Parameter of which the policy's weight parameter is given here."
   ::= { rserpoolENRPPoolElementEntry 9 }




Dreibholz & Mulik             Experimental                     [Page 21]


RFC 5525                  RSerPool MIB Module                 April 2009


rserpoolENRPPolicyLoad OBJECT-TYPE
   SYNTAX     RSerPoolPolicyLoadTC
   MAX-ACCESS read-only
   STATUS     current
   DESCRIPTION
      "The pool policy's load status for this pool element."
   REFERENCE
      "Section 3.8 of RFC 5354 defines the Member Selection Policy
      Parameter of which the policy's load parameter is given here."
   ::= { rserpoolENRPPoolElementEntry 10 }

rserpoolENRPPolicyLoadDeg OBJECT-TYPE
   SYNTAX     RSerPoolPolicyLoadTC
   MAX-ACCESS read-only
   STATUS     current
   DESCRIPTION
      "The pool policy's load degradation parameter for this pool
      element."
   REFERENCE
      "Section 3.8 of RFC 5354 defines the Member Selection Policy
      Parameter of which the policy's load degradation parameter is
      given here."
   ::= { rserpoolENRPPoolElementEntry 11 }

rserpoolENRPRegistrationLife OBJECT-TYPE
   SYNTAX     TimeTicks
   MAX-ACCESS read-only
   STATUS     current
   DESCRIPTION
      "The registration life of this pool element."
  REFERENCE
      "Section 3.10 of RFC 5354 defines the Registration Life."
   ::= { rserpoolENRPPoolElementEntry 12 }

rserpoolENRPHomeENRPServer OBJECT-TYPE
   SYNTAX     RSerPoolENRPServerIdentifierTC
   MAX-ACCESS read-only
   STATUS     current
   DESCRIPTION
      "The ID of the Home ENRP server of this pool element."
   REFERENCE
      "Section 3.10 of RFC 5354 defines the Home ENRP Server
      Identifier."
   ::= { rserpoolENRPPoolElementEntry 13 }

-- ## Definition of the ASAP transport address list table #########
rserpoolENRPASAPAddrTable OBJECT-TYPE
   SYNTAX     SEQUENCE OF RserpoolENRPASAPAddrTableEntry



Dreibholz & Mulik             Experimental                     [Page 22]


RFC 5525                  RSerPool MIB Module                 April 2009


   MAX-ACCESS not-accessible
   STATUS     current
   DESCRIPTION
      "A table listing of all IP addresses of the ASAP transport
      endpoint."
   REFERENCE
      "Section 3.10 of RFC 5354 defines the ASAP Transport Parameter of
      which the addresses are listed in this table."
   ::= { rserpoolENRPServers 5 }

rserpoolENRPASAPAddrTableEntry  OBJECT-TYPE
   SYNTAX     RserpoolENRPASAPAddrTableEntry
   MAX-ACCESS not-accessible
   STATUS     current
   DESCRIPTION
      "An IP address of the ASAP transport endpoint."
   REFERENCE
      "Section 3.10 of RFC 5354 defines the ASAP Transport Parameter of
      which an address is contained by this entry."
   INDEX {
      rserpoolENRPIndex,
      rserpoolENRPPoolIndex,
      rserpoolENRPPoolElementIndex,
      rserpoolENRPASAPAddrTableIndex }
   ::= { rserpoolENRPASAPAddrTable 1 }

RserpoolENRPASAPAddrTableEntry ::= SEQUENCE {
   rserpoolENRPASAPAddrTableIndex Unsigned32,
   rserpoolENRPASAPL3Type         InetAddressType,
   rserpoolENRPASAPL3Addr         InetAddress }

rserpoolENRPASAPAddrTableIndex OBJECT-TYPE
   SYNTAX     Unsigned32 (1..4294967295)
   MAX-ACCESS not-accessible
   STATUS     current
   DESCRIPTION
      "A unique identifier for the IP address of an ASAP transport
      endpoint."
   ::= { rserpoolENRPASAPAddrTableEntry 1 }

rserpoolENRPASAPL3Type OBJECT-TYPE
   SYNTAX     InetAddressType { ipv4(1), ipv6(2) }
   MAX-ACCESS read-only
   STATUS     current
   DESCRIPTION
      "The network-layer protocol (IPv4 or IPv6) of an IP address of
      an ASAP transport endpoint."
   REFERENCE



Dreibholz & Mulik             Experimental                     [Page 23]


RFC 5525                  RSerPool MIB Module                 April 2009


      "Section 3.10 of RFC 5354 defines the ASAP Transport Parameter of
      which the network-layer protocol number is given here."
   ::= { rserpoolENRPASAPAddrTableEntry 2 }

rserpoolENRPASAPL3Addr OBJECT-TYPE
   SYNTAX     InetAddress (SIZE(4|16))
   MAX-ACCESS read-only
   STATUS     current
   DESCRIPTION
      "The IP address of an ASAP transport endpoint.  The type of
      this address is given in rserpoolENRPASAPL3Type."
   REFERENCE
      "Section 3.10 of RFC 5354 defines the ASAP Transport Parameter of
      which the network-layer address (IPv4 or IPv6) is given here."
   ::= { rserpoolENRPASAPAddrTableEntry 3 }

-- ## Definition of the user transport address list table #########
rserpoolENRPUserAddrTable OBJECT-TYPE
   SYNTAX     SEQUENCE OF RserpoolENRPUserAddrTableEntry
   MAX-ACCESS not-accessible
   STATUS     current
   DESCRIPTION
      "A table listing of all IP addresses of the user
      transport endpoint."
   REFERENCE
      "Section 3.10 of RFC 5354 defines the User Transport Parameter of
      which the addresses are listed in this table."
   ::= { rserpoolENRPServers 6 }

rserpoolENRPUserAddrTableEntry  OBJECT-TYPE
   SYNTAX     RserpoolENRPUserAddrTableEntry
   MAX-ACCESS not-accessible
   STATUS     current
   DESCRIPTION
      "An IP address of the user transport endpoint."
   REFERENCE
      "Section 3.10 of RFC 5354 defines the User Transport Parameter of
      which an address is contained by this entry."
   INDEX {
      rserpoolENRPIndex,
      rserpoolENRPPoolIndex,
      rserpoolENRPPoolElementIndex,
      rserpoolENRPUserAddrTableIndex }
   ::= { rserpoolENRPUserAddrTable 1 }

RserpoolENRPUserAddrTableEntry ::= SEQUENCE {
   rserpoolENRPUserAddrTableIndex Unsigned32,
   rserpoolENRPUserL3Type         InetAddressType,



Dreibholz & Mulik             Experimental                     [Page 24]


RFC 5525                  RSerPool MIB Module                 April 2009


   rserpoolENRPUserL3Addr         InetAddress,
   rserpoolENRPUserL3Opaque       RSerPoolOpaqueAddressTC }

rserpoolENRPUserAddrTableIndex OBJECT-TYPE
   SYNTAX     Unsigned32 (1..4294967295)
   MAX-ACCESS not-accessible
   STATUS     current
   DESCRIPTION
      "A unique identifier for the IP address of a user transport
      endpoint."
   ::= { rserpoolENRPUserAddrTableEntry 1 }

rserpoolENRPUserL3Type OBJECT-TYPE
   SYNTAX     InetAddressType { unknown(0), ipv4(1), ipv6(2) }
   MAX-ACCESS read-only
   STATUS     current
   DESCRIPTION
      "The network-layer protocol (IPv4 or IPv6) of an IP address
      of a user transport endpoint.  Set to unknown for an opaque
      address."
   REFERENCE
      "Section 3.10 of RFC 5354 defines the User Transport Parameter of
      which the network-layer protocol number is given here."
   ::= { rserpoolENRPUserAddrTableEntry 2 }

rserpoolENRPUserL3Addr OBJECT-TYPE
   SYNTAX     InetAddress (SIZE(0|4|16))
   MAX-ACCESS read-only
   STATUS     current
   DESCRIPTION
      "The IP address of a user transport endpoint.  The type of
      this address is given in rserpoolENRPUserL3Type."
   REFERENCE
      "Section 3.10 of RFC 5354 defines the User Transport Parameter of
      which the network-layer address (IPv4 or IPv6) is given here."
   ::= { rserpoolENRPUserAddrTableEntry 3 }

rserpoolENRPUserL3Opaque OBJECT-TYPE
   SYNTAX     RSerPoolOpaqueAddressTC
   MAX-ACCESS read-only
   STATUS     current
   DESCRIPTION
      "The opaque address of a user transport endpoint."
   REFERENCE
      "Section 3.16 of RFC 5354 defines the opaque transport address."
   ::= { rserpoolENRPUserAddrTableEntry 4 }





Dreibholz & Mulik             Experimental                     [Page 25]


RFC 5525                  RSerPool MIB Module                 April 2009


-- ## Definition of ENRP address list table #######################
rserpoolENRPENRPAddrTable OBJECT-TYPE
   SYNTAX     SEQUENCE OF RserpoolENRPENRPAddrTableEntry
   MAX-ACCESS not-accessible
   STATUS     current
   DESCRIPTION
      "A table listing of all IP addresses of the ENRP
      transport endpoint."
   ::= { rserpoolENRPServers 7 }

rserpoolENRPENRPAddrTableEntry  OBJECT-TYPE
   SYNTAX     RserpoolENRPENRPAddrTableEntry
   MAX-ACCESS not-accessible
   STATUS     current
   DESCRIPTION
      "An IP address of the ENRP transport endpoint."
   INDEX {
      rserpoolENRPIndex,
      rserpoolENRPENRPAddrTableIndex }
   ::= { rserpoolENRPENRPAddrTable 1 }

RserpoolENRPENRPAddrTableEntry ::= SEQUENCE {
   rserpoolENRPENRPAddrTableIndex Unsigned32,
   rserpoolENRPENRPL3Type         InetAddressType,
   rserpoolENRPENRPL3Addr         InetAddress }

rserpoolENRPENRPAddrTableIndex OBJECT-TYPE
   SYNTAX     Unsigned32 (1..4294967295)
   MAX-ACCESS not-accessible
   STATUS     current
   DESCRIPTION
      "A unique identifier for the IP address of an ENRP transport
      endpoint."
   ::= { rserpoolENRPENRPAddrTableEntry 1 }

rserpoolENRPENRPL3Type OBJECT-TYPE
   SYNTAX     InetAddressType { ipv4(1), ipv6(2) }
   MAX-ACCESS read-only
   STATUS     current
   DESCRIPTION
      "The network-layer protocol (IPv4 or IPv6) of an IP address of
      an ENRP transport endpoint."
   REFERENCE
      "RFC 5353 defines the ENRP protocol."
   ::= { rserpoolENRPENRPAddrTableEntry 2 }






Dreibholz & Mulik             Experimental                     [Page 26]


RFC 5525                  RSerPool MIB Module                 April 2009


rserpoolENRPENRPL3Addr OBJECT-TYPE
   SYNTAX     InetAddress (SIZE(4|16))
   MAX-ACCESS read-only
   STATUS     current
   DESCRIPTION
      "The IP address of an ENRP transport endpoint.  The type of
      this address is given in rserpoolENRPENRPL3Type."
   REFERENCE
      "RFC 5353 defines the ENRP protocol."
   ::= { rserpoolENRPENRPAddrTableEntry 3 }

-- ## Definition of peer table ####################################
rserpoolENRPPeerTable OBJECT-TYPE
   SYNTAX     SEQUENCE OF RserpoolENRPPeerEntry
   MAX-ACCESS not-accessible
   STATUS     current
   DESCRIPTION
      "The table listing of a peer table."
   ::= { rserpoolENRPServers 8 }

rserpoolENRPPeerEntry OBJECT-TYPE
   SYNTAX     RserpoolENRPPeerEntry
   MAX-ACCESS not-accessible
   STATUS     current
   DESCRIPTION
      "A peer entry in the table listing of a peer table."
   INDEX { rserpoolENRPPeerIndex }
   ::= { rserpoolENRPPeerTable 1 }

RserpoolENRPPeerEntry ::= SEQUENCE {
   rserpoolENRPPeerIndex      Unsigned32,
   rserpoolENRPPeerIdentifier RSerPoolENRPServerIdentifierTC,
   rserpoolENRPPeerPort       InetPortNumber,
   rserpoolENRPPeerLastHeard  TimeTicks }

rserpoolENRPPeerIndex OBJECT-TYPE
   SYNTAX     Unsigned32 (1..4294967295)
   MAX-ACCESS not-accessible
   STATUS     current
   DESCRIPTION
      "A unique identifier for a peer entry in the table
      listing of a peer table."
   ::= { rserpoolENRPPeerEntry 1 }

rserpoolENRPPeerIdentifier OBJECT-TYPE
   SYNTAX     RSerPoolENRPServerIdentifierTC
   MAX-ACCESS read-only
   STATUS     current



Dreibholz & Mulik             Experimental                     [Page 27]


RFC 5525                  RSerPool MIB Module                 April 2009


   DESCRIPTION
      "The ENRP identifier of this peer."
   REFERENCE
      "RFC 5353 explains the usage of the ENRP server identifier."
   ::= { rserpoolENRPPeerEntry 2 }

rserpoolENRPPeerPort OBJECT-TYPE
   SYNTAX     InetPortNumber
   MAX-ACCESS read-only
   STATUS     current
   DESCRIPTION
      "The SCTP port number of the ENRP transport endpoint of
      this peer."
   REFERENCE
      "RFC 5353 defines the ENRP protocol."
   ::= { rserpoolENRPPeerEntry 3 }

rserpoolENRPPeerLastHeard OBJECT-TYPE
   SYNTAX     TimeTicks
   MAX-ACCESS read-only
   STATUS     current
   DESCRIPTION
      "The time since the reception of the last ENRP Presence
      message of this peer."
   REFERENCE
      "Section 4.1 of RFC 5353 defines the last heard value."
   ::= { rserpoolENRPPeerEntry 4 }

-- ## Definition of peer address list table #######################
rserpoolENRPPeerAddrTable OBJECT-TYPE
   SYNTAX     SEQUENCE OF RserpoolENRPPeerAddrTableEntry
   MAX-ACCESS not-accessible
   STATUS     current
   DESCRIPTION
      "A table listing of the peer endpoint addresses."
   ::= { rserpoolENRPServers 9 }

rserpoolENRPPeerAddrTableEntry  OBJECT-TYPE
   SYNTAX     RserpoolENRPPeerAddrTableEntry
   MAX-ACCESS not-accessible
   STATUS     current
   DESCRIPTION
      "A table listing of all IP addresses of the ENRP
      transport endpoint of a peer referenced by rserpoolENRPPeerIndex."
   INDEX {
      rserpoolENRPPeerIndex,
      rserpoolENRPPeerAddrTableIndex }
   ::= { rserpoolENRPPeerAddrTable 1 }



Dreibholz & Mulik             Experimental                     [Page 28]


RFC 5525                  RSerPool MIB Module                 April 2009


RserpoolENRPPeerAddrTableEntry ::= SEQUENCE {
   rserpoolENRPPeerAddrTableIndex Unsigned32,
   rserpoolENRPPeerL3Type         InetAddressType,
   rserpoolENRPPeerL3Addr         InetAddress }

rserpoolENRPPeerAddrTableIndex OBJECT-TYPE
   SYNTAX     Unsigned32 (1..4294967295)
   MAX-ACCESS not-accessible
   STATUS     current
   DESCRIPTION
      "A unique identifier for the IP address of a peer ENRP
      transport endpoint."
   ::= { rserpoolENRPPeerAddrTableEntry 1 }

rserpoolENRPPeerL3Type OBJECT-TYPE
   SYNTAX     InetAddressType { ipv4(1), ipv6(2) }
   MAX-ACCESS read-only
   STATUS     current
   DESCRIPTION
      "The network-layer protocol (IPv4 or IPv6) of an IP address
      of a peer ENRP transport endpoint."
   REFERENCE
      "RFC 5353 defines the ENRP protocol."
   ::= { rserpoolENRPPeerAddrTableEntry 2 }

rserpoolENRPPeerL3Addr OBJECT-TYPE
   SYNTAX     InetAddress (SIZE(4|16))
   MAX-ACCESS read-only
   STATUS     current
   DESCRIPTION
      "The IP address of a peer ENRP transport endpoint.  The type
      of this address is given in rserpoolENRPPeerL3Type."
   REFERENCE
      "RFC 5353 defines the ENRP protocol."
   ::= { rserpoolENRPPeerAddrTableEntry 3 }

-- ################################################################
-- #### Pool Elements Section                                  ####
-- ################################################################

-- ## Definition of the pool element table ########################
rserpoolPETable OBJECT-TYPE
   SYNTAX     SEQUENCE OF RserpoolPEEntry
   MAX-ACCESS not-accessible
   STATUS     current
   DESCRIPTION
      "The table listing of pool elements."
   ::= { rserpoolPoolElements 1 }



Dreibholz & Mulik             Experimental                     [Page 29]


RFC 5525                  RSerPool MIB Module                 April 2009


rserpoolPEEntry OBJECT-TYPE
   SYNTAX     RserpoolPEEntry
   MAX-ACCESS not-accessible
   STATUS     current
   DESCRIPTION
      "A pool element in the table listing of pool elements."
   INDEX { rserpoolPEIndex }
   ::= { rserpoolPETable 1 }

RserpoolPEEntry ::= SEQUENCE {
   rserpoolPEIndex              Unsigned32,
   rserpoolPEOperationScope     RSerPoolOperationScopeTC,
   rserpoolPEPoolHandle         RSerPoolPoolHandleTC,
   rserpoolPEIdentifier         RserpoolPoolElementIdentifierTC,
   rserpoolPEDescription        OCTET STRING,
   rserpoolPEUptime             TimeTicks,
   rserpoolPEASAPTransportPort  InetPortNumber,
   rserpoolPEUserTransportProto Unsigned32,
   rserpoolPEUserTransportPort  InetPortNumber,
   rserpoolPEUserTransportUse   RSerPoolTransportUseTypeTC,
   rserpoolPEPolicyID           RSerPoolPolicyIdentifierTC,
   rserpoolPEPolicyDescription  OCTET STRING,
   rserpoolPEPolicyWeight       RSerPoolPolicyWeightTC,
   rserpoolPEPolicyLoad         RSerPoolPolicyLoadTC,
   rserpoolPEPolicyLoadDeg      RSerPoolPolicyLoadTC,
   rserpoolPERegistrationLife   TimeTicks,
   rserpoolPEHomeENRPServer     RSerPoolENRPServerIdentifierTC }


rserpoolPEIndex OBJECT-TYPE
   SYNTAX     Unsigned32 (1..4294967295)
   MAX-ACCESS not-accessible
   STATUS     current
   DESCRIPTION
      "An integer to uniquely identify a pool element.  Note,
      that uniqueness of a pool element identifier in the pool
      is not enforced; therefore, this index is required here!"
   ::={ rserpoolPEEntry 1 }

rserpoolPEOperationScope OBJECT-TYPE
   SYNTAX     RSerPoolOperationScopeTC
   MAX-ACCESS read-only
   STATUS     current
   DESCRIPTION
      "The operation scope of this pool element."
   REFERENCE
      "Section 1.2 of RFC 3237 defines the term operation scope."
   ::= { rserpoolPEEntry 2 }



Dreibholz & Mulik             Experimental                     [Page 30]


RFC 5525                  RSerPool MIB Module                 April 2009


rserpoolPEPoolHandle OBJECT-TYPE
   SYNTAX     RSerPoolPoolHandleTC
   MAX-ACCESS read-write
   STATUS     current
   DESCRIPTION
      "The pool handle of this pool element.  Changing this object
      will update the pool element's pool handle and result in a
      re-registration.

      This object SHOULD be maintained in a persistent manner."
   REFERENCE
      "Section 1.2 of RFC 3237 defines the term pool handle."
   ::={ rserpoolPEEntry 3 }

rserpoolPEIdentifier OBJECT-TYPE
   SYNTAX     RserpoolPoolElementIdentifierTC
   MAX-ACCESS read-only
   STATUS     current
   DESCRIPTION
      "The pool element identifier of this pool element."
   REFERENCE
      "Section 3.10 of RFC 5354 defines the pool element identifier."
   ::={ rserpoolPEEntry 4 }

rserpoolPEDescription OBJECT-TYPE
   SYNTAX     OCTET STRING (SIZE (0..255))
   MAX-ACCESS read-write
   STATUS     current
   DESCRIPTION
      "A textual description of this pool element, e.g., its location
      and a contact address of its administrator.

      This object SHOULD be maintained in a persistent manner."
   ::= { rserpoolPEEntry 5 }

rserpoolPEUptime OBJECT-TYPE
   SYNTAX     TimeTicks
   MAX-ACCESS read-only
   STATUS     current
   DESCRIPTION
      "The ENRP service uptime of this pool element."
   ::= { rserpoolPEEntry 6 }

rserpoolPEASAPTransportPort OBJECT-TYPE
   SYNTAX     InetPortNumber
   MAX-ACCESS read-only
   STATUS     current
   DESCRIPTION



Dreibholz & Mulik             Experimental                     [Page 31]


RFC 5525                  RSerPool MIB Module                 April 2009


      "The SCTP port number of the ASAP endpoint of this pool element."
   REFERENCE
      "Section 3.10 of RFC 5354 defines the ASAP Transport Parameter of
      which the port number is given here."
   ::= { rserpoolPEEntry 7 }

rserpoolPEUserTransportProto OBJECT-TYPE
   SYNTAX     Unsigned32 (0..255)
   MAX-ACCESS read-only
   STATUS     current
   DESCRIPTION
      "The transport protocol number of the service endpoint
      of this pool element."
   REFERENCE
      "Section 3.10 of RFC 5354 defines the User Transport Parameter of
      which the transport protocol number is given here."
   ::= { rserpoolPEEntry 8 }

rserpoolPEUserTransportPort OBJECT-TYPE
   SYNTAX     InetPortNumber
   MAX-ACCESS read-only
   STATUS     current
   DESCRIPTION
      "The transport protocol's port number of the service
      endpoint of this pool element."
   REFERENCE
      "Section 3.10 of RFC 5354 defines the User Transport Parameter of
      which the port number is given here."
   ::= { rserpoolPEEntry 9 }

rserpoolPEUserTransportUse OBJECT-TYPE
   SYNTAX     RSerPoolTransportUseTypeTC
   MAX-ACCESS read-only
   STATUS     current
   DESCRIPTION
      "The transport use of the service endpoint of this pool element."
   REFERENCE
      "Section 3.10 of RFC 5354 defines the User Transport Parameter of
      which the transport use is given here."
   ::= { rserpoolPEEntry 10 }

rserpoolPEPolicyID OBJECT-TYPE
   SYNTAX     RSerPoolPolicyIdentifierTC
   MAX-ACCESS read-write
   STATUS     current
   DESCRIPTION
      "The pool policy of this pool element.  Changing this object
      will update the pool element's policy and result in a



Dreibholz & Mulik             Experimental                     [Page 32]


RFC 5525                  RSerPool MIB Module                 April 2009


      re-registration.

      This object SHOULD be maintained in a persistent manner."
   REFERENCE
      "Section 3.8 of RFC 5354 defines the Member Selection Policy
      Parameter of which the policy identifier is given here."
   ::= { rserpoolPEEntry 11 }

rserpoolPEPolicyDescription OBJECT-TYPE
   SYNTAX     OCTET STRING (SIZE (0..255))
   MAX-ACCESS read-write
   STATUS     current
   DESCRIPTION
      "The textual description of the pool policy of this pool element.

      This object SHOULD be maintained in a persistent manner."
   ::= { rserpoolPEEntry 12 }

rserpoolPEPolicyWeight OBJECT-TYPE
   SYNTAX     RSerPoolPolicyWeightTC
   MAX-ACCESS read-write
   STATUS     current
   DESCRIPTION
      "The pool policy's weight parameter for this pool element.
      Changing this object will update the pool element's policy
      weight setting and result in a re-registration.

      This object SHOULD be maintained in a persistent manner."
   REFERENCE
      "Section 3.8 of RFC 5354 defines the Member Selection Policy
      Parameter of which the policy's weight parameter is given here."
   ::= { rserpoolPEEntry 13 }

rserpoolPEPolicyLoad OBJECT-TYPE
   SYNTAX     RSerPoolPolicyLoadTC
   MAX-ACCESS read-only
   STATUS     current
   DESCRIPTION
      "The pool policy's load status for this pool element."
   REFERENCE
      "Section 3.8 of RFC 5354 defines the Member Selection Policy
      Parameter of which the policy's load parameter is given here."
   ::= { rserpoolPEEntry 14 }








Dreibholz & Mulik             Experimental                     [Page 33]


RFC 5525                  RSerPool MIB Module                 April 2009


rserpoolPEPolicyLoadDeg OBJECT-TYPE
   SYNTAX     RSerPoolPolicyLoadTC
   MAX-ACCESS read-write
   STATUS     current
   DESCRIPTION
      "The pool policy's load degradation parameter for this pool
      element.  Changing this object will update the pool element's
      load degradation setting and result in a re-registration.

      This object SHOULD be maintained in a persistent manner."
   REFERENCE
      "Section 3.8 of RFC 5354 defines the Member Selection Policy
      Parameter of which the policy's load degradation parameter is
      given here."
   ::= { rserpoolPEEntry 15 }

rserpoolPERegistrationLife OBJECT-TYPE
   SYNTAX     TimeTicks
   MAX-ACCESS read-write
   STATUS     current
   DESCRIPTION
      "The registration life of this pool element.  Changing this
      object will update the pool element's lifetime setting and
      result in a re-registration.

      This object SHOULD be maintained in a persistent manner."
   REFERENCE
      "Section 3.10 of RFC 5354 defines the Registration Life."
   ::= { rserpoolPEEntry 16 }

rserpoolPEHomeENRPServer OBJECT-TYPE
   SYNTAX     RSerPoolENRPServerIdentifierTC
   MAX-ACCESS read-only
   STATUS     current
   DESCRIPTION
      "The ID of the Home ENRP server of this pool element."
   REFERENCE
      "Section 3.10 of RFC 5354 defines the Home ENRP Server
      Identifier."
   ::= { rserpoolPEEntry 17 }

-- ## Definition of the ASAP transport address list table #########
rserpoolPEASAPAddrTable OBJECT-TYPE
   SYNTAX     SEQUENCE OF RserpoolPEASAPAddrTableEntry
   MAX-ACCESS not-accessible
   STATUS     current





Dreibholz & Mulik             Experimental                     [Page 34]


RFC 5525                  RSerPool MIB Module                 April 2009


   DESCRIPTION
      "A table listing of all IP addresses of the ASAP transport
      endpoint."
   REFERENCE
      "Section 3.10 of RFC 5354 defines the ASAP Transport Parameter of
      which the addresses are listed in this table."
   ::= { rserpoolPoolElements 2 }

rserpoolPEASAPAddrTableEntry  OBJECT-TYPE
   SYNTAX     RserpoolPEASAPAddrTableEntry
   MAX-ACCESS not-accessible
   STATUS     current
   DESCRIPTION
      "An IP address of the ASAP transport endpoint."
  REFERENCE
      "Section 3.10 of RFC 5354 defines the ASAP Transport Parameter of
      which an address is contained by this entry."
  INDEX {
      rserpoolPEIndex,
      rserpoolPEASAPAddrTableIndex }
   ::= { rserpoolPEASAPAddrTable 1 }

RserpoolPEASAPAddrTableEntry ::= SEQUENCE {
   rserpoolPEASAPAddrTableIndex Unsigned32,
   rserpoolPEASAPL3Type         InetAddressType,
   rserpoolPEASAPL3Addr         InetAddress }

rserpoolPEASAPAddrTableIndex OBJECT-TYPE
   SYNTAX     Unsigned32 (1..4294967295)
   MAX-ACCESS not-accessible
   STATUS     current
   DESCRIPTION
      "A unique identifier for the IP address of an ASAP transport
      endpoint."
   ::= { rserpoolPEASAPAddrTableEntry 1 }

rserpoolPEASAPL3Type OBJECT-TYPE
   SYNTAX     InetAddressType { ipv4(1), ipv6(2) }
   MAX-ACCESS read-only
   STATUS     current
   DESCRIPTION
      "The network-layer protocol (IPv4 or IPv6) of an IP address of
      an ASAP transport endpoint."
   REFERENCE
      "Section 3.10 of RFC 5354 defines the ASAP Transport Parameter of
      which the network-layer protocol number is given here."
   ::= { rserpoolPEASAPAddrTableEntry 2 }




Dreibholz & Mulik             Experimental                     [Page 35]


RFC 5525                  RSerPool MIB Module                 April 2009


rserpoolPEASAPL3Addr OBJECT-TYPE
   SYNTAX     InetAddress (SIZE(4|16))
   MAX-ACCESS read-only
   STATUS     current
   DESCRIPTION
      "The IP address of an ASAP transport endpoint.  The type of
      this address is given in rserpoolPEASAPL3Type."
   REFERENCE
      "Section 3.10 of RFC 5354 defines the ASAP Transport Parameter of
      which the network-layer address (IPv4 or IPv6) is given here."
   ::= { rserpoolPEASAPAddrTableEntry 3 }

-- ## Definition of the user transport address list table #########
rserpoolPEUserAddrTable OBJECT-TYPE
   SYNTAX     SEQUENCE OF RserpoolPEUserAddrTableEntry
   MAX-ACCESS not-accessible
   STATUS     current
   DESCRIPTION
      "A table listing of all IP addresses of the user
      transport endpoint."
   REFERENCE
      "Section 3.10 of RFC 5354 defines the User Transport Parameter of
      which the addresses are listed in this table."
   ::= { rserpoolPoolElements 6 }

rserpoolPEUserAddrTableEntry  OBJECT-TYPE
   SYNTAX     RserpoolPEUserAddrTableEntry
   MAX-ACCESS not-accessible
   STATUS     current
   DESCRIPTION
      "An IP address of the user transport endpoint."
  REFERENCE
      "Section 3.10 of RFC 5354 defines the User Transport Parameter of
      which an address is contained by this entry."
   INDEX {
      rserpoolPEIndex,
      rserpoolPEUserAddrTableIndex }
   ::= { rserpoolPEUserAddrTable 1 }

RserpoolPEUserAddrTableEntry ::= SEQUENCE {
   rserpoolPEUserAddrTableIndex Unsigned32,
   rserpoolPEUserL3Type         InetAddressType,
   rserpoolPEUserL3Addr         InetAddress,
   rserpoolPEUserL3Opaque       RSerPoolOpaqueAddressTC }

rserpoolPEUserAddrTableIndex OBJECT-TYPE
   SYNTAX     Unsigned32 (1..4294967295)
   MAX-ACCESS not-accessible



Dreibholz & Mulik             Experimental                     [Page 36]


RFC 5525                  RSerPool MIB Module                 April 2009


   STATUS     current
   DESCRIPTION
      "A unique identifier for the IP address of a user transport
      endpoint."
   ::= { rserpoolPEUserAddrTableEntry 1 }

rserpoolPEUserL3Type OBJECT-TYPE
   SYNTAX     InetAddressType { unknown(0), ipv4(1), ipv6(2) }
   MAX-ACCESS read-only
   STATUS     current
   DESCRIPTION
      "The network-layer protocol of an IP address of a user transport
      endpoint.  Set to unknown for opaque address."
   REFERENCE
      "Section 3.10 of RFC 5354 defines the User Transport Parameter of
      which the network-layer protocol number is given here."
   ::= { rserpoolPEUserAddrTableEntry 2 }

rserpoolPEUserL3Addr OBJECT-TYPE
   SYNTAX     InetAddress (SIZE(0|4|16))
   MAX-ACCESS read-only
   STATUS     current
   DESCRIPTION
      "The IP address of a user transport endpoint.  The type of
      this address is given in rserpoolPEUserL3Addr."
   REFERENCE
      "Section 3.10 of RFC 5354 defines the User Transport Parameter of
      which the network-layer address (IPv4 or IPv6) is given here."
   ::= { rserpoolPEUserAddrTableEntry 3 }

rserpoolPEUserL3Opaque OBJECT-TYPE
   SYNTAX     RSerPoolOpaqueAddressTC
   MAX-ACCESS read-only
   STATUS     current
   DESCRIPTION
      "The opaque address of a user transport endpoint."
   REFERENCE
      "Section 3.16 of RFC 5354 defines the opaque transport address."
   ::= { rserpoolPEUserAddrTableEntry 4 }

-- ################################################################
-- #### Pool Users Section                                     ####
-- ################################################################

-- ## Definition of the pool user table ###########################
rserpoolPUTable OBJECT-TYPE
   SYNTAX     SEQUENCE OF RserpoolPUEntry
   MAX-ACCESS not-accessible



Dreibholz & Mulik             Experimental                     [Page 37]


RFC 5525                  RSerPool MIB Module                 April 2009


   STATUS     current
   DESCRIPTION
      "The table listing of pool users."
   ::= { rserpoolPoolUsers 1 }

rserpoolPUEntry OBJECT-TYPE
   SYNTAX     RserpoolPUEntry
   MAX-ACCESS not-accessible
   STATUS     current
   DESCRIPTION
      "A pool user in the table listing of pool users."
   INDEX { rserpoolPUIndex }
   ::= { rserpoolPUTable 1 }

RserpoolPUEntry ::= SEQUENCE {
   rserpoolPUIndex          Unsigned32,
   rserpoolPUOperationScope RSerPoolOperationScopeTC,
   rserpoolPUPoolHandle     RSerPoolPoolHandleTC,
   rserpoolPUDescription    OCTET STRING,
   rserpoolPUUptime         TimeTicks }

rserpoolPUIndex OBJECT-TYPE
   SYNTAX     Unsigned32 (1..4294967295)
   MAX-ACCESS not-accessible
   STATUS     current
   DESCRIPTION
      "An integer to uniquely identify a pool user."
   ::= { rserpoolPUEntry 1 }

rserpoolPUOperationScope OBJECT-TYPE
   SYNTAX     RSerPoolOperationScopeTC
   MAX-ACCESS read-only
   STATUS     current
   DESCRIPTION
      "The operation scope of this pool user."
   REFERENCE
      "Section 1.2 of RFC 3237 defines the term operation scope."
   ::= { rserpoolPUEntry 2 }

rserpoolPUPoolHandle OBJECT-TYPE
   SYNTAX     RSerPoolPoolHandleTC
   MAX-ACCESS read-write
   STATUS     current








Dreibholz & Mulik             Experimental                     [Page 38]


RFC 5525                  RSerPool MIB Module                 April 2009


   DESCRIPTION
      "The pool handle of this pool user.  Changing this object
      will update the pool user's pool handle for all future
      sessions.

      This object SHOULD be maintained in a persistent manner."
   REFERENCE
      "Section 1.2 of RFC 3237 defines the term pool handle."
   ::={ rserpoolPUEntry 3 }

rserpoolPUDescription OBJECT-TYPE
   SYNTAX     OCTET STRING (SIZE (0..255))
   MAX-ACCESS read-write
   STATUS     current
   DESCRIPTION
      "A textual description of this pool user, e.g., its location
      and a contact address of its administrator.

      This object SHOULD be maintained in a persistent manner."
   ::= { rserpoolPUEntry 4 }

rserpoolPUUptime OBJECT-TYPE
   SYNTAX     TimeTicks
   MAX-ACCESS read-only
   STATUS     current
   DESCRIPTION
      "The ENRP service uptime of this pool user."
   ::= { rserpoolPUEntry 5 }

-- ## MIB conformance and compliance ##############################
rserpoolMIBCompliances OBJECT IDENTIFIER ::= {
   rserpoolMIBConformance 1
}

rserpoolMIBGroups OBJECT IDENTIFIER ::= {
   rserpoolMIBConformance 2
}

rserpoolMIBCompliance MODULE-COMPLIANCE
   STATUS  current
   DESCRIPTION
      "The compliance statement for SNMP entities that implement
      RSerPool."
   MODULE
   MANDATORY-GROUPS {
      rserpoolENRPGroup,
      rserpoolPEGroup,
      rserpoolPUGroup }



Dreibholz & Mulik             Experimental                     [Page 39]


RFC 5525                  RSerPool MIB Module                 April 2009


   ::= { rserpoolMIBCompliances 1 }

rserpoolENRPGroup OBJECT-GROUP
   OBJECTS {
      rserpoolENRPOperationScope,
      rserpoolENRPIdentifier,
      rserpoolENRPDescription,
      rserpoolENRPUptime,
      rserpoolENRPPort,
      rserpoolENRPASAPAnnouncePort,
      rserpoolENRPASAPAnnounceAddr,
      rserpoolENRPASAPAnnounceAddrType,
      rserpoolENRPENRPAnnounceAddrType,
      rserpoolENRPENRPAnnouncePort,
      rserpoolENRPENRPAnnounceAddr,

      rserpoolENRPPoolHandle,
      rserpoolENRPPoolElementID,

      rserpoolENRPASAPTransportPort,
      rserpoolENRPUserTransportProto,
      rserpoolENRPUserTransportUse,
      rserpoolENRPUserTransportPort,
      rserpoolENRPPolicyID,
      rserpoolENRPPolicyDescription,
      rserpoolENRPPolicyWeight,
      rserpoolENRPPolicyLoad,
      rserpoolENRPPolicyLoadDeg,
      rserpoolENRPRegistrationLife,
      rserpoolENRPHomeENRPServer,

      rserpoolENRPASAPL3Type,
      rserpoolENRPASAPL3Addr,

      rserpoolENRPUserL3Type,
      rserpoolENRPUserL3Addr,
      rserpoolENRPUserL3Opaque,

      rserpoolENRPENRPL3Type,
      rserpoolENRPENRPL3Addr,

      rserpoolENRPPeerIdentifier,
      rserpoolENRPPeerPort,
      rserpoolENRPPeerLastHeard,
      rserpoolENRPPeerL3Type,
      rserpoolENRPPeerL3Addr }
   STATUS current
   DESCRIPTION



Dreibholz & Mulik             Experimental                     [Page 40]


RFC 5525                  RSerPool MIB Module                 April 2009


      "The group contains all ENRP server instances
      running on the system"
   ::= { rserpoolMIBGroups 1 }

rserpoolPEGroup OBJECT-GROUP
   OBJECTS {
      rserpoolPEOperationScope,
      rserpoolPEPoolHandle,
      rserpoolPEIdentifier,
      rserpoolPEDescription,
      rserpoolPEUptime,
      rserpoolPEASAPTransportPort,
      rserpoolPEUserTransportProto,
      rserpoolPEUserTransportPort,
      rserpoolPEUserTransportUse,
      rserpoolPEPolicyID,
      rserpoolPEPolicyDescription,
      rserpoolPEPolicyWeight,
      rserpoolPEPolicyLoad,
      rserpoolPEPolicyLoadDeg,
      rserpoolPERegistrationLife,
      rserpoolPEHomeENRPServer,

      rserpoolPEASAPL3Type,
      rserpoolPEASAPL3Addr,

      rserpoolPEUserL3Type,
      rserpoolPEUserL3Addr,
      rserpoolPEUserL3Opaque }
   STATUS current
   DESCRIPTION
      "The group contains all pool element instances
      running on the system"
   ::= { rserpoolMIBGroups 2 }

rserpoolPUGroup OBJECT-GROUP
   OBJECTS { rserpoolPUOperationScope,
      rserpoolPUPoolHandle,
      rserpoolPUDescription,
      rserpoolPUUptime }
   STATUS current
   DESCRIPTION
      "The group contains all pool user instances
      running on the system"
   ::= { rserpoolMIBGroups 3 }

END




Dreibholz & Mulik             Experimental                     [Page 41]


RFC 5525                  RSerPool MIB Module                 April 2009


7.  Operational Considerations

   The RSerPool MIB is an Experimental track MIB module, since the
   RSerPool documents are Experimental RFCs.

8.  Security Considerations

   There are a number of management objects defined in this MIB module
   with a MAX-ACCESS clause of read-write and/or read-create.  Such
   objects may be considered sensitive or vulnerable in some network
   environments.  The support for SET operations in a non-secure
   environment without proper protection can have a negative effect on
   network operations.  These are the tables and objects and their
   sensitivity/vulnerability:

      rserpoolENRPDescription (textual description change)

      rserpoolPEPoolHandle (pool handle of pool element change, similar
      to ASAP)

      rserpoolPEDescription (textual description change)

      rserpoolPEPolicyID (pool element ID change, similar to ASAP)

      rserpoolPEPolicyDescription (textual description change)

      rserpoolPEPolicyWeight (policy weight change, similar to ASAP)

      rserpoolPEPolicyLoadDeg (policy load degradation change, similar
      to ASAP)

      rserpoolPERegistrationLife (registration lifetime change, similar
      to ASAP)

      rserpoolPUPoolHandle (pool handle of accessed pool change, similar
      to ASAP)

      rserpoolPUDescription (textual description change)

   The security implications of changing these items are similar to
   changes via ASAP; the corresponding security implications are
   described in the threats document [RFC5355].  Modifying the textual
   descriptions of components may result in wrong administrator
   decisions upon malicious information.







Dreibholz & Mulik             Experimental                     [Page 42]


RFC 5525                  RSerPool MIB Module                 April 2009


   Some of the readable objects in this MIB module (i.e., objects with a
   MAX-ACCESS other than not-accessible) may be considered sensitive or
   vulnerable in some network environments.  It is thus important to
   control even GET and/or NOTIFY access to these objects and possibly
   to even encrypt the values of these objects when sending them over
   the network via SNMP.  Read access reveals the same information which
   is also available by ASAP and ENRP access.  The security implications
   of these two protocols are explained in detail by the threats
   document [RFC5355].

   SNMP versions prior to SNMPv3 did not include adequate security.
   Even if the network itself is secure (for example by using IPsec),
   even then, there is no control as to who on the secure network is
   allowed to access and GET/SET (read/change/create/delete) the objects
   in this MIB module.

   It is RECOMMENDED that implementers consider the security features as
   provided by the SNMPv3 framework (see [RFC3410], section 8),
   including full support for the SNMPv3 cryptographic mechanisms (for
   authentication and privacy).

   Further, deployment of SNMP versions prior to SNMPv3 is NOT
   RECOMMENDED.  Instead, it is RECOMMENDED to deploy SNMPv3 and to
   enable cryptographic security.  It is then a customer/operator
   responsibility to ensure that the SNMP entity giving access to an
   instance of this MIB module is properly configured to give access to
   the objects only to those principals (users) that have legitimate
   rights to indeed GET or SET (change/create/delete) them.

9.  IANA Considerations

   The MIB module in this document uses the following IANA-assigned
   OBJECT IDENTIFIER values recorded in the SMI Numbers registry:

   Descriptor OBJECT IDENTIFIER Value
   ----------  -----------------------
   rserpoolMIB { experimental 125 }

10.  Acknowledgments

   The authors would like to express a special note of thanks to Phillip
   Conrad and Kevin Pinzhoffer for their efforts in the early formation
   of this document.  Furthermore, the authors would like to thank Bert
   Wijnen and Dan Romascanu for their valuable comments on this
   document.  Finally, the authors would like to thank Nihad Cosic, Dirk
   Hoffstadt, Michael Kohnen, Jobin Pulinthanath, Randall Stewart,
   Michael Tuexen, and Xing Zhou for their support.




Dreibholz & Mulik             Experimental                     [Page 43]


RFC 5525                  RSerPool MIB Module                 April 2009


11.  References

11.1.  Normative References

   [RFC2119]       Bradner, S., "Key words for use in RFCs to Indicate
                   Requirement Levels", BCP 14, RFC 2119, March 1997.

   [RFC2578]       McCloghrie, K., Ed., Perkins, D., Ed., and J.
                   Schoenwaelder, Ed., "Structure of Management
                   Information Version 2 (SMIv2)", STD 58, RFC 2578,
                   April 1999.

   [RFC2579]       McCloghrie, K., Ed., Perkins, D., Ed., and J.
                   Schoenwaelder, Ed., "Textual Conventions for SMIv2",
                   STD 58, RFC 2579, April 1999.

   [RFC2580]       McCloghrie, K., Perkins, D., and J. Schoenwaelder,
                   "Conformance Statements for SMIv2", STD 58, RFC 2580,
                   April 1999.

   [RFC4001]       Daniele, M., Haberman, B., Routhier, S., and J.
                   Schoenwaelder, "Textual Conventions for Internet
                   Network Addresses", RFC 4001, February 2005.

   [RFC5352]       Stewart, R., Xie, Q., Stillman, M., and M. Tuexen,
                   "Aggregate Server Access Protocol (ASAP)", RFC 5352,
                   September 2008.

   [RFC5353]       Xie, Q., Stewart, R., Stillman, M., Tuexen, M., and
                   A. Silverton, "Endpoint Handlespace Redundancy
                   Protocol (ENRP)", RFC 5353, September 2008.

   [RFC5354]       Stewart, R., Xie, Q., Stillman, M., and M. Tuexen,
                   "Aggregate Server Access Protocol (ASAP) and Endpoint
                   Handlespace Redundancy Protocol (ENRP) Parameters",
                   RFC 5354, September 2008.

   [RFC5356]       Dreibholz, T. and M. Tuexen, "Reliable Server Pooling
                   Policies", RFC 5356, September 2008.

11.2.  Informative References

   [RFC3237]       Tuexen, M., Xie, Q., Stewart, R., Shore, M., Ong, L.,
                   Loughney, J., and M. Stillman, "Requirements for
                   Reliable Server Pooling", RFC 3237, January 2002.






Dreibholz & Mulik             Experimental                     [Page 44]


RFC 5525                  RSerPool MIB Module                 April 2009


   [RFC3410]       Case, J., Mundy, R., Partain, D., and B. Stewart,
                   "Introduction and Applicability Statements for
                   Internet-Standard Management Framework", RFC 3410,
                   December 2002.

   [RFC5351]       Lei, P., Ong, L., Tuexen, M., and T. Dreibholz, "An
                   Overview of Reliable Server Pooling Protocols",
                   RFC 5351, September 2008.

   [RFC5355]       Stillman, M., Gopal, R., Guttman, E., Sengodan, S.,
                   and M. Holdrege, "Threats Introduced by Reliable
                   Server Pooling (RSerPool) and Requirements for
                   Security in Response to Threats", RFC 5355,
                   September 2008.

   [Dre2006]       Dreibholz, T., "Reliable Server Pooling --
                   Evaluation, Optimization and Extension of a Novel
                   IETF Architecture", Ph.D. Thesis University of
                   Duisburg-Essen, Faculty of Economics, Institute for
                   Computer Science and Business Information Systems,
                   March 2007, <http://duepublico.uni-duisburg-essen.de/
                   servlets/DerivateServlet/Derivate-16326/
                   Dre2006-final.pdf>.

   [LCN2005]       Dreibholz, T. and E. Rathgeb, "On the Performance of
                   Reliable Server Pooling Systems", Proceedings of the
                   30th IEEE Local Computer Networks Conference,
                   November 2005.

   [IJHIT2008]     Dreibholz, T. and E. Rathgeb, "An Evaluation of the
                   Pool Maintenance Overhead in Reliable Server Pooling
                   Systems", International Journal of Hybrid Information
                   Technology (IJHIT) Volume 1, Number 2, April 2008.

   [RSerPoolPage]  Dreibholz, T., "Thomas Dreibholz's RSerPool Page",
                   <http://tdrwww.iem.uni-due.de/dreibholz/rserpool/>.

   [SNMPMIBS]      Perkins, D. and E. McGinnis, "Understanding SNMP
                   MIBs", 1997.












Dreibholz & Mulik             Experimental                     [Page 45]


RFC 5525                  RSerPool MIB Module                 April 2009


Authors' Addresses

   Thomas Dreibholz
   University of Duisburg-Essen, Institute for Experimental Mathematics
   Ellernstrasse 29
   45326 Essen, Nordrhein-Westfalen
   Germany

   Phone: +49-201-1837637
   Fax:   +49-201-1837673
   EMail: dreibh@iem.uni-due.de
   URI:   http://www.iem.uni-due.de/~dreibh/


   Jaiwant Mulik
   Delaware State University
   CIS Department
   Room 306A, Science Center North
   1200 N. DuPont Hwy
   Dover, DE  19904
   USA

   Phone: +1-302-857-7910
   Fax:   +1-302-857-6552
   EMail: jaiwant@mulik.com
   URI:   http://netlab.cis.desu.edu

























Dreibholz & Mulik             Experimental                     [Page 46]