README for XFree86 4.2.0 on OpenBSD Matthieu Herrb Last modified on: 16 January 2002 1. What and Where is XFree86? XFree86 is the Open Source port of X.Org's X11R6.6 release that supports sev- eral UNIX(R) and UNIX-like (such as Linux, the BSDs and Solaris x86) operat- ing systems on Intel and other platforms. See the Copyright Notice. The sources for XFree86 4.2.0 are available by anonymous ftp from: ftp://ftp.XFree86.org/pub/XFree86/4.2.0 Binaries for OpenBSD/i386 3.0 and later are available from: ftp://ftp.XFree86.org/pub/XFree86/4.2.0/binaries/OpenBSD A list of mirror sites is provided by http://www.xfree86.org/MIRRORS.shtml XFree86 also builds on other OpenBSD architectures. See section Building on other architectures (section 8.2, page 1) for details. 2. Bug Reports for This Document Send email to (Matthieu Herrb) or if you have comments or suggestions about this file and we'll revise it. 3. New OS dependent features See the Release Notes for non-OS dependent new features in XFree86 4.2.0. 3.1 New OS dependent features in 4.2 o Support for OpenBSD/macppc on the ATI Rage128 based Power Macintosh. o Support for building clients on OpenBSD/sparc64. 3.2 New OS dependent features in 4.0.3 o Support for the wscons console driver in post 2.8 OpenBSD. o A fix for multi-threaded libraries support. 3.3 New OS dependent features in 4.0.2 o Support for the OpenBSD ports tree, o Preliminary support for the macppc architecture (clients build and work, the server doesn't work yet), o xdm now writes an utmp entry, o startx now creates an Xauthority magic cookie for the display. 3.4 New OS dependent features in 4.0.1 o Several features from the OpenBSD X11 tree were merged into xdm: o support for Kerberos IV authentication o use the arc4random(4) random number generator o add a new resource "allowRootLogin", which can be used to disable root logins through xdm o log failed logins to syslogd o verify that the shell is valid using /etc/shell o verify that the account hasn't expired o The Xsun server can be built again on OpenBSD/sparc. 3.5 New OS dependent features in 4.0 o Multi-thread safe libraries are built by default on OpenBSD 2.6 and later, o Preliminary APM support. 3.6 New OS dependent features in 3.9.18 o Support for USB mices has been added on OpenBSD. o Soft-booting secondary cards through the int10 BIOS interface is now possible using the x86emu real mode emulator. 3.7 New OS dependent features in 3.9.17 o Silken mouse is supported for serial mices, and, under post 2.6 OpenBSD- current for PS/2 mices. o MTRR Write Combining is enabled under post 2.6 OpenBSD-current. 4. Installing the Binaries Refer to the Installation Document for detailed installation instructions. 5. Configuring X for Your Hardware The /etc/X11/XF86Config file tells the X server what kind of monitor, video card and mouse you have. You must create it to tell the server what specific hardware you have. You'll need info on your hardware: o Your mouse type, baud rate and its /dev entry. o The video card's chipset (e.g. ET4000, S3, etc). o Your monitor's sync frequencies. The recommended way to generate an XF86Config file is to use the xf86cfg utility. The xf86config text utility is still there for the (few) cases where xf86cfg can't be used. Also, there is a sample file installed as /usr/X11R6/lib/X11/XF86Config.eg, which can be used as a starting point. For details about the XF86Config file format, refer to the XF86Config(5) man- ual page. Once you've set up a XF86Config file, you can fine tune the video modes with the xvidtune utility. 5.1 About mouse configuration XFree86 4.2.0 has support for the mouse driver included in the new wscons console driver introduced by OpenBSD-2.9. Specify ``wsmouse'' as the proto- col and ``/dev/wsmouse0'' as the device in /etc/X11/XF86Config if you're using OpenBSD-2.9 or later with a PS/2 or USB mouse. See README.mouse for general instruction on mouse configuration in XFree86. 6. Running X 6.1 Starting xdm, the display manager To start the display manager, log in as root on the console and type: ``xdm -nodaemon''. You can start xdm automatically on bootup by changing the line xdm_flags=NO # for normal use: xdm_flags="" to: xdm_flags="" # for normal use: xdm_flags="" in /etc/rc.conf. Note that the binary distributions of XFree86 for OpenBSD on ftp.xfree86.org and its mirrors don't include support for the XDM-AUTHORIZATION-1 protocol, because of the US export rules. 6.2 Running X without the display manager The easiest way for new users to start X windows is to type: ``startx >& startx.log''. Error messages are lost unless you redirect them because the server takes over the screen. To get out of X windows, type: ``exit'' in the console xterm. You can cus- tomize your X by creating .xinitrc, .xserverrc, and .twmrc files in your home directory as described in the xinit and startx man pages. 7. Kernel Support for X To make sure X support is enabled under OpenBSD, the following line must be in your config file in /sys/arch/i386/conf: option XSERVER option APERTURE 7.1 Console drivers The server supports the standard OpenBSD/i386 console drivers: pcvt and wscons. They are detected at runtime and no configuration of the server itself is required. The pcvt console driver is the default in OpenBSD up to OpenBSD 2.8. It offers several virtual consoles and international keyboard support. OpenBSD 2.9 and later has switched to the wscons console driver. This console driver has a pcvt compatibility mode for X support. 7.2 Aperture Driver By default OpenBSD includes the BSD 4.4 kernel security feature that disables access to the /dev/mem device when in multi-user mode. But the XFree86 server requires linear access to the display memory in most cases. OpenBSD now requires the aperture driver to be enabled for all X servers, because the aperture driver also controls access to the I/O ports of the video boards. To enable the aperture driver, once included in the kernel, set machdep.allowaperture=2 in /etc/sysctl.conf. See the xf86(4) manual page for details. Another (less recommended) way to enable linear memory and I/O ports access is to disable the kernel security feature by initializing securelevel to -1 in /etc/rc.securelevel. Caveat: the aperture driver only allows one access at a time (so that the system is in the same security state once X is launched). This means that if you run multiple servers on multiple virtual terminals, only the first one will have linear memory access. Set securelevel to -1 if you need more that one X server at a time. 7.3 MIT-SHM OpenBSD supports System V shared memory. If XFree86 detects this support in your kernel, it will support the MIT-SHM extension. To add support for system V shared memory to your kernel add the lines: # System V-like IPC options SYSVMSG options SYSVSEM options SYSVSHM to your kernel config file. 8. Rebuilding the XFree86 Distribution You should configure the distribution by editing xc/config/cf/host.def before compiling. To compile the sources, invoke ``make World'' in the xc directory." 8.1 Console drivers XFree86 has a configuration option to select the console drivers to use in host.def: o if you're using pccons only put: #define XFree86ConsoleDefines -DPCCONS_SUPPORT o if you're using pcvt only put: #define XFree86ConsoleDefines -DPCVT_SUPPORT If you don't define XFree86ConsoleDefines in host.def the pccons and pcvt drivers will be supported by default. Native support for the wscons console driver found on OpenBSD/macppc and on OpenBSD/i386 2.9 and later is built by adding: #define XFree86ConsoleDefines -DWSCONS_SUPPORT to xc/config/host.def before rebuilding the server. For the i386, you should include both pcvt and wscons support in order to use the pcvt compatibility mode of wscons: #define XFree86ConsoleDefines -DPCVT_SUPPORT -DWSCONS_SUPPORT 8.2 Building on other architectures XFree86 also compiles on other OpenBSD architectures. Note that OpenBSD project now has its own source tree, based on the XFree86 source tree, with some local modifications. You may want to start with this tree to rebuild from sources. The OpenBSD XF4 source tree is available by anoncvs from all OpenBSD anoncvs servers. See http://www.openbsd.org/anon- cvs.html for details on anoncvs. 8.2.1 XFree86 on OpenBSD/macppc The XFree86 server is currently known to work on the G4 Macs and new iBooks with ATI Rage 128 cards running OpenBSD 3.0 or later. Other machines are more or less untested. Earlier OpenBSD versions lack some kernel support for it. Use xf86config to build a /etc/X11/XF86Config file before starting the server for the first time. Tou configure the keyboard, the protocol should be specified as wskbd and the device as /dev/wskbd0. Using a wsmux device as the keyboard device doesn't work (yet). Use macintosh as XkbModel. For the Titanium Powerbook G4, you can try the following mode line in /etc/X11/XF86Config to match the flat panel resolution: Modeline "1152x768" 78.741 1152 1173 1269 1440 768 769 772 800 +HSync +VSync You need to set securelevel to -1 in the /etc/rc.securelevel configuration file to run XFree86 on OpenBSD/macppc. 9. Building New X Clients The easiest way to build a new client (X application) is to use xmkmf if an Imakefile is included in the sources. Type ``xmkmf -a'' to create the Make- files, check the configuration if necessary and type ``make''. Whenever you install additional man pages you should update whatis.db by running ``make- whatis /usr/X11R6/man''. 10. Thanks Many thanks to all people who contributed to make XFree86 work on *BSD, in particular, David Dawes, Pace Willison, Amancio Hasty, Christoph Robitschko, Nate Williams, Rod Grimes, Jack Velte and Michael Smith. Generated from XFree86: xc/programs/Xserver/hw/xfree86/doc/sgml/OpenBSD.sgml,v 1.24 2002/01/16 22:35:17 herrb Exp $